Traxxas 3.3 Engine Ips Shaft W/Pull Start

This is the Traxxas TRX 3.3 Racing Engine with Pull Starter.

FEATURES:
For use in all Traxxas TRX2.5 and TRX 3.3 equipped automobiles
Pull starter can be eliminated to install the EZ Start
60% more peak power than the TRX2.5, with nearly 50% more power
    under the curve for strong linear acceleration
Round rear exhaust with one-piece IPS crankshaft
Composite body slide valve carburetor with high-volume air filter
Blue anodized aluminum cooling head with molded head protector

INCLUDES:
Traxxas TRX 3.3 Racing Engine with Pull Starter and glow plug
One instruction handbook (TRAZ5300)
One service support guide and parts lis.
One set of engine decals
One engine burglary DVD
One little bottle of air filter oil
One air filter

NEEDS:
Vehicle fuel with 10%, 20% or 33% nitro material

SPECIFICATIONS:
Displacement: .20 cu in (3.3cc)
Practical RPM: N/A
Output: N/A
Weight: 10.9oz (305g)
Distance in between installing holes same side: 0.39" (10mm)
Distance in between installing holes opposite side: 1.2" (32mm)
Distance from center of engine to front bearing: 1.2" (32mm)
Distance/bottom of installing flanges/top of cylinder head: 3.5" (88mm
Width of installing flanges: 44mm

REMARKS:
Other versions of the TRX 3.3 engine include;
    #5404 Single Shaft without Starter, TRAG5404
    #5406 Multi-Shaft without Starter, TRAG5406
    #5409 Multi-Shaft w/Recoil Pull Starter, TRAG5409

Below is one more product that compliments the product being gone over.



This is the DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery Load
with Requirement Connector.

FEATURES:
Ideal sport pack for vehicles, trucks and boats

INCLUDES:
DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery with Standard
    Adapter

NEEDS:
NiMH compatible charger such as the Duratrax Onyx series

SPECIFICATIONS:
Capacity: 3000mAh
Number of Cells in Series: 6
Rated Voltage: 7.2V
Min. Release Voltage: 5.4V
Maximum Recommended Charge Current: 4 amps
Release Lead: 14AWG 2.7" (70mm) long wire w/Standard connector
Load Dimensions: 5.2 x 1.9 x 0.9" (131 x 47 x 24mm)
Weight: 13 oz (360 g)
Number of Welds per Connection: 6 area welds
Cell Size: Sub-C

This product compliments the main item here.

Cone Split Beveled

Replacement SPLIT BEVEL CONE for the Traxxas Nitro Vee Boat. This cone is
part of the engine assembly. (Image .12)

PLAN
INCLUDES:
1-Diagonal Cone

FUNCTIONS:
Black steel building and construction
Diagonal cone shape with split on one side

REMARKS:
Diagonal cone sits in front of the flywheel
7/19/94sk

Numerous others have purchased this product in addition to the product that you are presently reviewing.

T Maxx .15 To 2.5 Upgrade Kit

This is the Pro .15 to TRX 2.5 engine conversion set from Traxxas.
It allows you to install the more recent 2.5 engine to an older T-Maxx.

FUNCTIONS:
Tuned pipe, bellcrank, & throttle servo horn made from plastic
Linkage wire made from steel

INCLUDES:
One Plastic Tune Pipe w/Wire Hanger (TRAG5152)
One Exhaust Header w/Screws & O-ring (TRAG5140)
One Exhaust Coupler (TRAG5246)
One Slide Carb Link Bellcrank (TRAC5167)
One Slide Carb Linkage Set (TRAC5168)
One Drill Bit for drilling Bellcrank Post installing holes
Two Tie-Straps for installing Exhaust Coupler
One 90-degree pressure fitting
One 3x10mm maker cap screw w/washer
One instruction sheet
One drilling design template sheet

NEEDS:
2.5 engine stock clutch system and stock engine install

SPECIFICATIONS:
Tune Pipe Length: 101.6mm (4")
Header Pipe Outer Diameter: 13mm (.51")
Drill Bit size: 3.175mm (.125")

REMARKS:
If EZ Start system is needed, use TRAP5271