Traxxas 3.3 Engine Ips Shaft W/Pull Start

This is the Traxxas TRX 3.3 Racing Engine with Pull Starter.

FEATURES:
For use in all Traxxas TRX2.5 and TRX 3.3 equipped cars
Pull starter can be gotten rid of to install the EZ Start
60% more peak power than the TRX2.5, with nearly 50% more power
    under the curve for strong linear velocity
Round rear exhaust with one-piece IPS crankshaft
Composite body slide valve carburetor with high-volume air filter
Blue anodized aluminum cooling head with molded head protector

INCLUDES:
Traxxas TRX 3.3 Racing Engine with Pull Beginner and radiance plug
One guideline handbook (TRAZ5300)
One service assistance guide and parts lis.
One set of engine decals
One engine burglary DVD
One little bottle of air filter oil
One air filter

NEEDS:
Automobile fuel with 10%, 20% or 33% nitro content

SPECS:
Displacement: .20 cu in (3.3cc)
Practical RPM: N/A
Output: N/A
Weight: 10.9oz (305g)
Distance between mounting holes very same side: 0.39" (10mm)
Distance between mounting holes opposite side: 1.2" (32mm)
Distance from center of engine to front bearing: 1.2" (32mm)
Distance/bottom of mounting flanges/top of cylinder head: 3.5" (88mm
Width of mounting flanges: 44mm

REMARKS:
Other variations of the TRX 3.3 engine include;
    #5404 Single Shaft without Beginner, TRAG5404
    #5406 Multi-Shaft without Beginner, TRAG5406
    #5409 Multi-Shaft w/Recoil Pull Beginner, TRAG5409

Here is one more item that compliments the item being talked about.



This is the DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery Load
with Standard Connector.

FEATURES:
Ideal sport pack for vehicles, trucks and boats

INCLUDES:
DuraTrax NiMH 7.2V 3000mAh Onyx Stick Battery with Conventional
    Adapter

NEEDS:
NiMH compatible charger such as the Duratrax Onyx series

SPECS:
Capability: 3000mAh
Variety of Cells in Series: 6
Ranked Voltage: 7.2V
Minutes. Discharge Voltage: 5.4V
Maximum Recommended Charge Current: 4 amps
Discharge Lead: 14AWG 2.7" (70mm) long wire w/Standard port
Load Measurements: 5.2 x 1.9 x 0.9" (131 x 47 x 24mm)
Weight: 13 oz (360 g)
Number of Welds per Connection: 6 spot welds
Cell Size: Sub-C

This item compliments the main item here.

Cone Split Beveled

Replacement SPLIT BEVEL CONE for the Traxxas Nitro Vee Boat. This cone is
part of the engine assembly. (Image .12)

PACKAGE
INCLUDES:
1-Beveled Cone

FUNCTIONS:
Black steel building and construction
Beveled cone shape with split on one side

REMARKS:
Beveled cone sits in front of the flywheel
7/19/94sk

Numerous others have bought this item in addition to the item that you are presently checking out.

T Maxx .15 To 2.5 Upgrade Kit

This is the Pro .15 to TRX 2.5 engine conversion set from Traxxas.
It enables you to mount the newer 2.5 engine to an older T-Maxx.

FUNCTIONS:
Tuned pipeline, bellcrank, & throttle servo horn made of plastic
Linkage wire made of steel

INCLUDES:
One Plastic Tune Pipeline w/Wire Hanger (TRAG5152)
One Exhaust Header w/Screws & O-ring (TRAG5140)
One Exhaust Coupler (TRAG5246)
One Slide Carbohydrate Link Bellcrank (TRAC5167)
One Slide Carbohydrate Linkage Set (TRAC5168)
One Drill Bit for drilling Bellcrank Post mounting holes
Two Tie-Straps for mounting Exhaust Coupler
One 90-degree pressure fitting
One 3x10mm device cap screw w/washer
One guideline sheet
One drilling template sheet

NEEDS:
2.5 engine stock clutch system and stock engine mount

SPECS:
Tune Pipeline Length: 101.6mm (4")
Header Pipeline Outer Size: 13mm (.51")
Drill Bit size: 3.175mm (.125")

REMARKS:
If EZ Start system is required, utilize TRAP5271