Traxxas Driveshafts, Rear, Steel-Spline Constant-Velocity (Complete Asse

This is a pair of optional Rear Driveshafts
for the 1/10 scale Traxxas Slash 4x4.

FUNCTIONS:
Harddened steel construction

CONSISTS OF:
Two Rear Driveshafts

Regularly acquired with the thing that you are presently reading about.

Driveshafts, Front, Steel-Spline Constant Velocity (Complete Ass

This is a pair of optional Front Driveshafts
for the 1/10 scale Traxxas Slash 4x4.

FUNCTIONS:
Harddened steel construction

CONSISTS OF:
Two Front Driveshafts

The listed below thing also pairs actually well with the thing being talked about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

Lots of others have acquired this thing along with the thing that you are presently reading about.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Set for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One Steel Disc
Three Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Instructions

REQUIRES:
Disassembly of slipper clutch

Get this thing to enhance the one you are reading about.

Hex Hubs Blue Alum (2) Slash

These are Optional Blue Anodized Aluminum Wheel Hex Hubs for Traxxas vehicles
such as the Stampede, Rustler, 4-Tec, and other older Traxxas kits.

FEATURES:
Blue aluminum construction

CONSISTS OF:
Two hex hubs
Four axle pins

REQUIRES:
Assembly onto axles.

SPECS:
Hex Length: 12mm (.47")
Hex Density: 6.1mm (.24")
Axle Pin Length: 9.6mm (.38")

COMMENTS:
These hubs could be used with other vehicles using the exact same
    pin/hex design. These hubs Will Not work on the T-Maxx or E-Maxx.

This thing is regularly acquired with the above stated thing.

Slash 2Wd Low Cg Chassis Conversion Kit

This is the optional Low CG Conversion Set for the
1/10 scale 2WD Traxxas Slash.

FEATURES:
Reduces the chassis 1" (25.4mm) for much better handling and higher
    catching speed
Holds battery and electronics as deep in chassis as possible
45% lower battery position

CONSISTS OF:
Chassis
Lower Chassis
Two Nerf Bars
Battery Hold Down with Front and Rear Retainers
Two Front Shock Springs
Hardware and Instructions

Lots of others have acquired this thing along with the thing that you are presently reading about.

Locked Diff Hub Spool For Traxxas Slash, Rustler, Stampede

    This is the Hot-Racing Differential Locker Spool
for the Traxxas 2WD Outlaw, Slash, Electric Rustler and Electric Stampede.

FEATURES:
Stainless-steel output shaft
CNC machined 6061-T6 aluminum locker plate
Installs in differential case to get rid of diff action
Provides much better acceleration, climbing, wandering, and wheelie possible
Recommended for off-road use only
Thirty day limited service warranty starting at date of purchase-valid
    in the United States only

CONSISTS OF:
Differential Locker Spool

You will enjoy this product if you have the product earlier mentioned.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Get this thing to enhance the one you are reading about.

Anaconda Tirew/All-Star Bk Chrome Elec Rr 1 Left & 1 Righ

This is a pair of the Traxxas Rear All Star Wheels
and Anaconda Tires for Electric Vehicles.

FEATURES:
Black chrome plated plastic, 5 spoke design
Split X-Pattern tread tires with foam inserts

CONSISTS OF:
One left and one right all-star wheel with Anaconda tires and
    foam inserts for electrical vehicles

REQUIRES:
Installing on car

SPECIFICATIONS:
Diameter: 3.93" (100mm)
Width: 1.96" (50mm)