Traxxas Driveshaft, Center, Aluminum (

This is the Aluminum Center Driveshaft for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Hollow aluminum building and construction
Anodized blue in color

INCLUDES:
One Aluminum Center Driveshaft

NEEDS:
Installation on the automobile

SPECIFICATIONS:
Length: 215mm (8.5")
Size: 8.3mm (0.33")

Regularly purchased with the item that you are presently reviewing.

Hold Down, Tall Battery Slash

This is the Hold Down Battery Set for the 2WD Traxxas Slash.
**Will not deal with the Traxxas Slash 4x4.**

FEATURES:
Black nylon building and construction

INCLUDES:
One Battery Hold Down
One Retainer Hold Down
One Battery Post
One Foam Spacer
One Angled Body Clip

NEEDS:
Installation on the chassis

This item compliments the main item right here.

Cover, Center Driveshaft (Clea

This is the Center Driveshaft Cover for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Clear nylon building and construction

INCLUDES:
One Center Driveshaft Cover

NEEDS:
Installation over driveshaft

SPECIFICATIONS:
Length: 210mm (8.3")
Width: 15mm (0.59")

This is a wonderful addition to the item presently being discussed.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Nylon building and construction
Black in color
.8 Module pitch

INCLUDES:
One 54T 0.8 Pitch Spur Gear

NEEDS:
Assembly onto automobile

Want one more fantastic item to enhance the above stated item?

Motor Heat Sink

This is the initial replacement motor heatsink for the Traxxas Bad guy IV.
AXY
4/8/92

This item is frequently purchased with the above stated item.

Drive Hub, Center, Rear (1)/ F

This is the Front and Rear Center Drive Hub Set for use on the
Traxxas Slash 4x4 Vehicles.

FEATURES:
Nylon and steel building and construction

INCLUDES:
One Front Center Drive Hub
One Rear Center Drive Hub
One Screw Pin

NEEDS:
Installation in drive assembly

Want one more fantastic item to enhance the above stated item?

Bumper, Front/ Bumper Mount, F

This is the Front Bumper and Mount for the Traxxas Slash 4x4.

FEATURES:
Hardened plastic building and construction
Black in color

INCLUDES:
One Front bumper
One Front bumper mount

NEEDS:
Installation on chassis

This is a wonderful addition to the item presently being discussed.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

Want one more fantastic item to enhance the above stated item?

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Construction
Protected with blue rubber seals

INCLUDES:
Two Ball Bearings

NEEDS:
Assembly to automobile

SPECIFICATIONS:
Inner Size: 10mm
External Size: 15mm
Side Density: 4mm

COMMENTS:
These bearings are used to support the Main Clutch (one required).

This item compliments the main item right here.

Traxxas Slash 4X4 Rear Bumper-Blue

This is the optional RPM Rear Bumper for use on the Traxxas Slash 4x4.
Will NOT deal with the Slash 2WD.

FEATURES:
Nylon building and construction
Blue in color

INCLUDES:
One Left Side Bumper Support
One Right Side Bumper Support
One Rear Bumper
8 3x16mm Buttonhead Screws
One Upper Bumper Mount
One Lower Bumper Mount

NEEDS:
Installation on the automobile

COMMENTS:
Likewise readily available in: Black (RPMC0122)
Chrome (RPMC0123)