Traxxas Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FUNCTIONS:
Totally put together
Plastic telescoping driveshaft with steel universals
Blue rubber boot shields telescoping sections from dirt
Attaches to the differential with one screw pin
Functions on the front or rear, right or left of car

CONSISTS OF:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Guideline sheet

NEEDS:
Installing on chassis

This item compliments the main item right here.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Nylon building
Black in color
.8 Module pitch

CONSISTS OF:
One 54T 0.8 Pitch Spur Gear

NEEDS:
Assembly onto car

Numerous others have actually acquired this item together with the item that you are currently reviewing.

12 X 18 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

    These are the replacement Wheel Center Ball Bearings for
the Traxxas Nitro Revo Monster Truck.

FEATURES:
Stainless Steel Building and construction
Blue Rubber Sealed

CONSISTS OF:
Two 12mm x 18mm Blue Sealed Stainless Wheel Center Bearings

NEEDS:
Assembly onto Car

SPECIFICATIONS:
Outer Size: 18mm (0.70")
Inner Size: 12mm (0.47")
Thickness: 4mm (0.15")

REMARKS:
These are for the Within the Wheel Hubs, the Truck Needs
Four Overall of these Bearings.

The listed below item also sets really well with the item being reviewed.

Half Shaft Set Left Or Right Revo

This is a replacement Half Shaft Set for the Traxxas Revo Truck.
This plan consists of a part of the telescoping drive shafts.

FEATURES:
Black plastic building
Blue rubber shaft boots

CONSISTS OF:
Two half shaft assemblies

NEEDS:
Nothing. These are direct replacement parts.

SPECS:
Length: 120mm (4.7")

Often acquired with the item that you are currently reviewing.

Bbs Blue Rubber Sealed 6 X 13M

This is a set of Traxxas 6x13x5mm Ball Bearings
for use on the E-Revo

FUNCTIONS:
Stainless Steel bearing building
Blue rubber dirt shields

CONSISTS OF:
(2) 6x13x5mm ball bearings Part #5180

SPECIFICATIONS:
Inside size: 6mm (0.24")
Outside size: 13mm (0.51")
Width: 5mm (0.20")

Get this item to enhance the one you are reading about.

Axle Carriers Left & Right (1 Ea) Revo

This is the set of Axle Carriers and Steering Blocks for the Traxxas Revo.
The axle carriers and steering blocks support the stub axles and bolt
    to the upper and lower suspension arms at each wheel.

FEATURES:
Changes damaged axle carriers and steering blocks.
Constructed of black plastic.

INCLUDES:
One set of axle carriers and steering blocks for the Traxxas Revo.

REQUIRES:
Bolting to each suspension arm, setting up two 12x18mm ball
    bearings, stub axles, and pillow balls.

Below is a wonderful item that numerous others have actually bought at the very same time.

Axle Carriers Use Larger 6 X 1

These are the Optional Axle Carriers L & R for
use on the Traxxas Revo series.

FEATURES:
Nylon Building and construction
Black in Color
Permits for Oversized Bearing use

CONSISTS OF:
One Left Axle Carrier
One Right Axle Carrier
Four Dust Boot Retainers
Two Bearing Spacers

NEEDS:
Installation

Often acquired with the item that you are currently reviewing.

E-Revo Body Prographix

    This is a PROGRAPHIX Body for the Traxxas E-Revo
Covers and Safeguards the Vehicle.

FEATURES:
Lexan building
Pre-painted graphics
Body mount holes pre-drilled
Pre-cut
Protective movie covers beyond body after finish and is gotten rid of
    after completion of paint task

CONSISTS OF:
One painted graphics E-Revo Body
One decal set

NEEDS:
Lexan safe spray or brush-on paint
Traxxas E-Revo

SPECIFICATIONS:
Length: 500mm (19.7")
Width: 185mm (7.28")
Height: 125mm (4.92")

COMMENT:
Graphics are pre-painted. Needs paint and final
decal application.