Traxxas Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building and construction

CONSISTS OF:
Front driveshaft assembly
Screw pin

REQUIRES:
Setup on car

The listed below thing also sets truly well with the thing being reviewed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building and construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on car

This is a great enhancement to the thing presently being reviewed.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Lots of others have purchased this thing in addition to the thing that you are presently reading about.

Slipper Clutch Complete Stampede 4X4

This is the Complete Slipper Clutch Set for the Slash 4X4 from Traxxas.

FEATURES:
Complete slipper clutch assembly
Pre-assembled

CONSISTS OF:
2 nuts
1 spring
1 metal plate
1 pin
3 pads
2 washers
54T spur equipment

REQUIRES:
Setup in car

Here is a fantastic thing that lots of others have bought at the same time.

Steering Blocks, Left & Right

These are the Steering Blocks for the Traxxas Slash 4x4.

FUNCTIONS:
Hardened plastic building and construction
Black in color

CONSISTS OF:
Two steering blocks

REQUIRES:
Setup on steering assembly

SPECS:
Length: 35mm (1.38")
Width: 32mm (1.26")

You will certainly like this product if you have the product previously discussed.

Front Or Rear A-Arms For Traxxas Slash 4X4 And Rustler 4X4, Blac

These are the optional RPM Strong Front/Rear A-Arms
for the Traxxas Slash 4x4.

FUNCTIONS:
Black in color
Plastic constrution

CONSISTS OF:
Two Front/Rear A-Arms

REQUIRES:
Setup at front or rear suspension

SPECS:
Length: 3.96" (100.5mm)
Width: 1.79" (45.5mm) at best point
Thickness: 0.31" (8mm)

REMARKS:
Likewise offered in Blue (RPMC0705)

This thing is often purchased with the above mentioned thing.

Body Mount (1)/Body Mount Pos

This is the Front/Rear Body Mount for the Traxxas Slash 4x4.

FUNCTIONS:
Hardened plastic building and construction
Black in color

CONSISTS OF:
One body install
Two body install posts

REQUIRES:
Setup on chassis

SPECS:
Length: 126mm (4.96")
Width: 24mm (0.95")

Frequently purchased with the thing that you are presently reading about.

Caster Blocks (C-Hubs), Left &

These are the Caster Blocks (C-Hubs) for the Traxxas Slash 4x4.

FUNCTIONS:
Hardened plastic building and construction
Black in color

CONSISTS OF:
One left caster block
One right caster block

REQUIRES:
Setup on Slash

SPECS:
Length: 49mm (1.93")
Width: 29.5mm (1.16")

This is a great enhancement to the thing presently being reviewed.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Nylon building and construction
Black in color
.8 Module pitch

CONSISTS OF:
One 54T 0.8 Pitch Spur Gear

REQUIRES:
Assembly onto car

Frequently purchased with the thing that you are presently reading about.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building and construction
Shielded with blue rubber seals

CONSISTS OF:
Two Ball Bearings

REQUIRES:
Assembly to car

SPECS:
Inner Diameter: 10mm
Outer Diameter: 15mm
Side Thickness: 4mm

REMARKS:
These bearings are used to support the Primary Clutch (one needed).