Traxxas Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

CONSISTS OF:
Front driveshaft assembly
Screw pin

REQUIRES:
Installation on vehicle

The listed below item also sets really well with the item being gone over.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on vehicle

This is a amazing addition to the item currently being gone over.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Numerous others have bought this item together with the item that you are currently checking out.

Slipper Clutch Complete Stampede 4X4

This is the Total Slipper Clutch Set for the Slash 4X4 from Traxxas.

FEATURES:
Total slipper clutch assembly
Pre-assembled

CONSISTS OF:
2 nuts
1 spring
1 metal plate
1 pin
3 pads
2 washers
54T spur gear

REQUIRES:
Installation in vehicle

Right here is a fantastic item that numerous others have purchased the exact same time.

Steering Blocks, Left & Right

These are the Steering Blocks for the Traxxas Slash 4x4.

FEATURES:
Hardened plastic construction
Black in color

CONSISTS OF:
2 steering blocks

REQUIRES:
Installation on steering assembly

SPECS:
Length: 35mm (1.38")
Width: 32mm (1.26")

You will love this product if you have the product above pointed out.

Fr/Re A-Arms Black Slash/Stampede 4X4

These are the optional RPM Strong Front/Rear A-Arms
for the Traxxas Slash 4x4.

FEATURES:
Black in color
Plastic constrution

CONSISTS OF:
2 Front/Rear A-Arms

REQUIRES:
Installation at front or rear suspension

SPECS:
Length: 3.96" (100.5mm)
Width: 1.79" (45.5mm) at largest point
Thickness: 0.31" (8mm)

COMMENTS:
Also readily available in Blue (RPMC0705)

This item is regularly bought with the above mentioned item.

Body Mount (1)/Body Mount Pos

This is the Front/Rear Body Mount for the Traxxas Slash 4x4.

FEATURES:
Hardened plastic construction
Black in color

CONSISTS OF:
One body mount
2 body mount posts

REQUIRES:
Installation on chassis

SPECS:
Length: 126mm (4.96")
Width: 24mm (0.95")

Regularly bought with the item that you are currently checking out.

Caster Blocks (C-Hubs), Left &

These are the Caster Blocks (C-Hubs) for the Traxxas Slash 4x4.

FEATURES:
Hardened plastic construction
Black in color

CONSISTS OF:
One left caster block
One right caster block

REQUIRES:
Installation on Slash

SPECS:
Length: 49mm (1.93")
Width: 29.5mm (1.16")

This is a amazing addition to the item currently being gone over.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Equipment
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Nylon construction
Black in color
.8 Module pitch

CONSISTS OF:
One 54T 0.8 Pitch Spur Equipment

REQUIRES:
Assembly onto vehicle

Regularly bought with the item that you are currently checking out.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Construction
Protected with blue rubber seals

CONSISTS OF:
2 Ball Bearings

REQUIRES:
Assembly to vehicle

SPECS:
Inner Diameter: 10mm
Outer Diameter: 15mm
Side Thickness: 4mm

COMMENTS:
These bearings are utilized to support the Primary Clutch (one needed).