Traxxas Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

INCLUDES:
Rear driveshaft assembly
Screw pin

NEEDS:
Installation on car

Get this thing to improve the one you read around.

Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

INCLUDES:
Front driveshaft assembly
Screw pin

NEEDS:
Installation on car

The listed below thing additionally pairs truly well with the thing being talked about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

You will certainly love this product if you have the product earlier discussed.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that connect the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

Numerous others have actually acquired this thing in addition to the thing that you are currently reading about.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Thickness: 0.5mm

Want an additional excellent thing to match the above discussed thing?

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Complete Planetary Gear Differential With Steel Ring Gear
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal gear shafts
Metal and plastic main differential

INCLUDES:
Main differential with steel ring gear
Planetary gears and shafts
Sun gears and shafts
Silicone grease

NEEDS:
Installation on the car

COMMENTS:
For main differential w/ steel ring - TRAC6380
Planet gear shafts - TRAC6382
Silicon grease _- TRAC6037

This thing is often acquired with the above discussed thing.

30T Idler Gear Steel

This is the optional Steel Idler Gear for lots of Traxxas Vehicles.

FEATURES:
Steel construction

INCLUDES:
One steel 30T idler gear

NEEDS:
Installation on car

The listed below thing additionally pairs truly well with the thing being talked about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL variation of the Rustler
or Stampede.

This thing praises the above talked about thing.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic construction
Steel idler shaft

INCLUDES:
One gearbox
One idler shaft

COMMENTS:
This part fit the standard and XL variation of both the Stampede
and Rustler.

This is a fantastic enhancement to the thing currently being talked about.

49Mm Turnbuckles Camber Link Rr

These are the Traxxas 49mm Turnbuckle Camber Hyperlinks
for the Bandit, Rustler VXL and Stampede VXL.

FEATURES:
Metal and Nylon Building
Silver and Black in Color
Put together w/Rod Ends

INCLUDES:
2 rear 49mm (82mm center to center) turnbuckles

NEEDS:
Installation on the car