Traxxas Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on automobile

Get this product to boost the one you are reading around.

Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel construction

CONSISTS OF:
Front driveshaft assembly
Screw pin

REQUIRES:
Setup on automobile

The below product also sets actually well with the product being gone over.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

You will certainly love this thing if you have the thing previously mentioned.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that connect the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

Numerous others have purchased this product together with the product that you are presently reviewing.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Thickness: 0.5mm

Want one more great product to match the above stated product?

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Total Planetary Gear Differential With Steel Ring Gear
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal equipment shafts
Metal and plastic primary differential

CONSISTS OF:
Main differential with steel ring equipment
Planetary equipments and shafts
Sun equipments and shafts
Silicone grease

REQUIRES:
Setup on the automobile

COMMENTS:
For primary differential w/ steel ring - TRAC6380
World equipment shafts - TRAC6382
Silicon grease _- TRAC6037

This product is often purchased with the above stated product.

30T Idler Gear Steel

This is the optional Steel Idler Gear for many Traxxas Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One steel 30T idler equipment

REQUIRES:
Setup on automobile

The below product also sets actually well with the product being gone over.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

This product compliments the above gone over product.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic construction
Steel idler shaft

CONSISTS OF:
One gearbox
One idler shaft

COMMENTS:
This part fit the standard and XL version of both the Stampede
and Rustler.

This is a amazing enhancement to the product presently being gone over.

49Mm Turnbuckles Camber Link Rr

These are the Traxxas 49mm Turnbuckle Camber Hyperlinks
for the Bandit, Rustler VXL and Stampede VXL.

FEATURES:
Metal and Nylon Building and construction
Silver and Black in Color
Put together w/Rod Ends

CONSISTS OF:
Two rear 49mm (82mm center to center) turnbuckles

REQUIRES:
Setup on the automobile