Traxxas Drive Hub, Frt, Hardened Steel (1) Screw Pin, (1) Fits Slash

This is the Front Hardened Steel Drive Center for use on the Traxxas Slash 4x4.

FEATURES:
Solidified steel building and construction

CONSISTS OF:
One Drive Center
One Screw Pin

REQUIRES:
Installation on the car

SPECIFICATIONS:
Length: 19mm (0.75")
Size: 12mm (0.47")

The listed below item also pairs truly well with the item being gone over.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

This is a fantastic enhancement to the item presently being gone over.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building
Protected with blue rubber seals

CONSISTS OF:
Two Ball Bearings

REQUIRES:
Assembly to car

SPECIFICATIONS:
Inner Size: 10mm
Outer Size: 15mm
Side Thickness: 4mm

REMARKS:
These bearings are used to support the Primary Clutch (one required).

Below is a wonderful item that several others have actually purchased the same time.

Suspension Pin Set, Complete Frt & Rr Includes Frt & Rr Swa

This is the Suspension Pin Set for the Traxxas Slash 4X4.
The hinge pins hold the suspension arms to the bulkheads

FEATURES:
Resilient steel building and construction
Silver in color

CONSISTS OF:
Four 51.5mm pins
Four 30mm pins

REQUIRES:
Installation on the Slash 4x4

This item is often bought with the above discussed item.

6 X 12 X 4Mm Ball Bearing (2) Blue Rubber Sheild R Evo

This is a 6X12mm Ball Bearing Set from Traxxas.

FEATURES:
Steel building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) ball bearings, Part #5117

SPECIFICATIONS:
Inside size: 6mm
Outdoors size: 12mm
Width: 4mm

REMARKS:
This bearing set is used in the transmission and differentials of
    the Revo.

Get this item to enhance the one you are reading around.

8 X 16 X 5Mm Ball Bearing (2) Blue Rubber Sheild R Evo

    These are the replacement Differential Bearings for
the Traxxas Nitro Revo Beast Truck.

FEATURES:
Stainless Building
Blue Rubber Sealed

CONSISTS OF:
Two 8mm x 16mm Rubber Sealed Bearings

REQUIRES:
Assembly onto Automobile

SPECIFICATIONS:
Inner Size: 8mm (0.31")
Outer Size: 16mm (0.62")
Thickness: 5mm (0.19")

This item is often bought with the above discussed item.

Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building and construction

CONSISTS OF:
Front driveshaft assembly
Screw pin

REQUIRES:
Installation on car

This item compliments the main item right here.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building and construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on car

Below is one more item that compliments the item being gone over.

Ring Gear, Differential/ Pinio

This is the Differential Ring and Pinion Gear for use on the
Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One Differential Ring Gear
One Differential Pinion Gear

REQUIRES:
Installation in differential assembly

SPECIFICATIONS:
Pinion Gear:
Tooth: 13T
Inner Size: 5mm (0.20")
Ring Gear:
Tooth: 37T
Inner Size: 6mm (0.24")

The listed below item also pairs truly well with the item being gone over.

Housings, Differential, Front

This is the Front Differential Housing for the Traxxas Slash 4x4.

FEATURES:
Solidified plastic building and construction
Black in color

CONSISTS OF:
Two front differential housing halves

REQUIRES:
Installation around assembled differential components