Traxxas Caster Blocks (C-Hubs), Left &

These are the Caster Blocks (C-Hubs) for the Traxxas Slash 4x4.

FUNCTIONS:
Hardened plastic building and construction
Black in color

INCLUDES:
One left caster block
One right caster block

REQUIRES:
Setup on Slash

SPECS:
Length: 49mm (1.93")
Width: 29.5mm (1.16")

This thing compliments the above discussed thing.

Steering Blocks, Left & Right

These are the Steering Blocks for the Traxxas Slash 4x4.

FUNCTIONS:
Hardened plastic building and construction
Black in color

INCLUDES:
Two steering blocks

REQUIRES:
Setup on steering assembly

SPECS:
Length: 35mm (1.38")
Width: 32mm (1.26")

Get this thing to improve the one you read about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

This is a fantastic enhancement to the thing presently being discussed.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Construction
Protected with blue rubber seals

INCLUDES:
Two Ball Bearings

REQUIRES:
Assembly to automobile

SPECS:
Inner Size: 10mm
External Size: 15mm
Side Density: 4mm

COMMENTS:
These bearings are utilized to support the Primary Clutch (one needed).

This thing compliments the main item right here.

Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building and construction

INCLUDES:
Front driveshaft assembly
Screw pin

REQUIRES:
Setup on automobile

Get this thing to improve the one you read about.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building and construction

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on automobile

Lots of others have purchased this thing along with the thing that you are presently reading about.

49Mm Turnbuckles Camber Link Rr

These are the Traxxas 49mm Turnbuckle Camber Links
for the Bandit, Rustler VXL and Stampede VXL.

FEATURES:
Metal and Nylon Construction
Silver and Black in Color
Assembled w/Rod Ends

INCLUDES:
Two rear 49mm (82mm center to center) turnbuckles

REQUIRES:
Setup on the automobile

Here is a wonderful thing that numerous others have purchased the same time.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Density: 0.5mm

This thing is often purchased with the above pointed out thing.

Cover, Center Driveshaft (Clea

This is the Center Driveshaft Cover for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Clear nylon building and construction

INCLUDES:
One Center Driveshaft Cover

REQUIRES:
Setup over driveshaft

SPECS:
Length: 210mm (8.3")
Width: 15mm (0.59")

This thing compliments the main item right here.

39Mm Camber Link Turnbuckles (Fr) Slash, Bandit, Stampede

These are the 39mm Turnbuckle Camber Links
for the Traxxas Stampede and Rustler VXL.

FEATURES:
Metal and Nylon Construction
Silver and Black in Color
Assembled w/Rod Ends

INCLUDES:
Two front 39mm (69mm center to center) turnbuckles and instruction
    sheet

REQUIRES:
Setup on the automobile

This is a fantastic enhancement to the thing presently being discussed.

Hex Hubs Blue Alum (2) Slash

These are Optional Blue Anodized Aluminum Wheel Hex Hubs for Traxxas automobiles
such as the Stampede, Rustler, 4-Tec, and other older Traxxas kits.

FEATURES:
Blue aluminum building and construction

INCLUDES:
Two hex centers
4 axle pins

REQUIRES:
Assembly onto axles.

SPECS:
Hex Length: 12mm (.47")
Hex Density: 6.1mm (.24")
Axle Pin Length: 9.6mm (.38")

COMMENTS:
These centers could be utilized with other automobiles making use of the exact same
    pin/hex design. These centers Will Not work on the T-Maxx or E-Maxx.