Traxxas Caster Blocks (C-Hubs), Left &

These are the Caster Blocks (C-Hubs) for the Traxxas Slash 4x4.

FEATURES:
Solidified plastic construction
Black in color

INCLUDES:
One left caster block
One right caster block

REQUIRES:
Setup on Slash

SPECIFICATIONS:
Length: 49mm (1.93")
Width: 29.5mm (1.16")

This product compliments the above gone over product.

Steering Blocks, Left & Right

These are the Steering Blocks for the Traxxas Slash 4x4.

FEATURES:
Solidified plastic construction
Black in color

INCLUDES:
2 steering obstructs

REQUIRES:
Setup on guiding assembly

SPECIFICATIONS:
Length: 35mm (1.38")
Width: 32mm (1.26")

Get this product to enhance the one you read about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

This is a wonderful enhancement to the product currently being gone over.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Construction
Shielded with blue rubber seals

INCLUDES:
2 Ball Bearings

REQUIRES:
Assembly to automobile

SPECIFICATIONS:
Inner Size: 10mm
Outer Size: 15mm
Side Density: 4mm

REMARKS:
These bearings are used to support the Main Clutch (one needed).

This product compliments the main item here.

Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

INCLUDES:
Front driveshaft assembly
Screw pin

REQUIRES:
Setup on automobile

Get this product to enhance the one you read about.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on automobile

Lots of others have actually gotten this product together with the product that you are currently reviewing.

49Mm Turnbuckles Camber Link Rr

These are the Traxxas 49mm Turnbuckle Camber Links
for the Outlaw, Rustler VXL and Stampede VXL.

FEATURES:
Metal and Nylon Construction
Silver and Black in Color
Assembled w/Rod Ends

INCLUDES:
2 rear 49mm (82mm center to center) turnbuckles

REQUIRES:
Setup on the automobile

Below is a terrific product that numerous others have actually bought at the very same time.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

This product is often gotten with the above stated product.

Cover, Center Driveshaft (Clea

This is the Center Driveshaft Cover for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Clear nylon construction

INCLUDES:
One Center Driveshaft Cover

REQUIRES:
Setup over driveshaft

SPECIFICATIONS:
Length: 210mm (8.3")
Width: 15mm (0.59")

This product compliments the main item here.

39Mm Camber Link Turnbuckles (Fr) Slash, Bandit, Stampede

These are the 39mm Turnbuckle Camber Links
for the Traxxas Stampede and Rustler VXL.

FEATURES:
Metal and Nylon Construction
Silver and Black in Color
Assembled w/Rod Ends

INCLUDES:
2 front 39mm (69mm center to center) turnbuckles and instruction
    sheet

REQUIRES:
Setup on the automobile

This is a wonderful enhancement to the product currently being gone over.

Hex Hubs Blue Alum (2) Slash

These are Optional Blue Anodized Aluminum Wheel Hex Hubs for Traxxas automobiles
such as the Stampede, Rustler, 4-Tec, and other older Traxxas kits.

FEATURES:
Blue aluminum construction

INCLUDES:
2 hex centers
Four axle pins

REQUIRES:
Assembly onto axles.

SPECS:
Hex Length: 12mm (.47")
Hex Density: 6.1mm (.24")
Axle Pin Length: 9.6mm (.38")

REMARKS:
These centers could be used with other automobiles making use of the exact same
    pin/hex design. These centers Will Not deal with the T-Maxx or E-Maxx.