Traxxas Box, Receiver For Stmpd, Rstlr, Bandt

This is the Receiver Box for usage on the
Traxxas Stampede, Rustler, and Bandit Vehicles.

FEATURES:
Nylon building
Black in color

INCLUDES:
One Receiver Box
One Rubber Seal
Foam Cushioning
Two 2.5x8mm Cap Head Screws
Two 3x10mm Cap Head Screws
Two 2.5x10mm Cap Head Screws
One Tube of Grease
Instruction sheet

REQUIRES:
Setup on the vehicle

SPECS:
Length: 78mm (3.07")
Width: 35mm (1.4")
Height: 33mm (1.3")

This thing praises the main item here.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Get this thing to enhance the one you are reading about.

Hc Connector M/F (1) Available Only From

This is the Male/Female Traxxas Connectors Plugs Just (No Wires).

FEATURES:
Shrouded wire connections (no diminish tube required)
Wide area, gold-plated terminals
Reverse polarity security makes it impossible to link in reverse
Textured surface for simple gripping
Compatible with high-current 12-gauge wire
Secure, favorable locking spring packed terminals for constant
    contact
Several locking barbs keep terminals secure

INCLUDES:
One black female plastic connector
One black male plastic connector
Two sets of gold metal pins
Instruction sheet

REQUIRES:
Soldering wires to the metal pins

The below thing also sets really well with the thing being gone over.

Mounting Plate For Stampede Esc

This is the ESC and Receiver Box Mounting Plate for usage on the
Traxxas Stampede.

FEATURES:
Nylon building
Black in color

INCLUDES:
One Mounting Plate
4 3x7.5mm Flanged Button Head Screws
Two 3x12mm Flanged Button Head Screws

REQUIRES:
Setup on the vehicle

SPECS:
Length: 87mm (3.4")
Width: 60mm (2.4")
Height: 10mm (0.39")

This is a wonderful addition to the thing currently being gone over.

Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel building
Natural color

INCLUDES:
Two front axles

REQUIRES:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Size: 5mm

REMARKS:
These will not work for the nitro variations. For that axle, usage
    TRAC2536.

This thing is regularly acquired with the above pointed out thing.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on vehicle

This thing praises the main item here.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for lots of Traxxas Vehicles.

FEATURES:
Steel building

INCLUDES:
One steel 30T idler equipment

REQUIRES:
Setup on vehicle

Numerous others have actually acquired this thing in addition to the thing that you are currently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.