Traxxas Box, Receiver For Stmpd, Rstlr, Bandt

This is the Receiver Box for usage on the
Traxxas Stampede, Rustler, and Bandit Vehicles.

FEATURES:
Nylon construction
Black in color

INCLUDES:
One Receiver Box
One Rubber Seal
Foam Padding
2 2.5x8mm Cap Head Screws
2 3x10mm Cap Head Screws
2 2.5x10mm Cap Head Screws
One Tube of Grease
Direction sheet

REQUIRES:
Installation on the automobile

SPECS:
Length: 78mm (3.07")
Width: 35mm (1.4")
Height: 33mm (1.3")

This item compliments the main item here.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Get this item to improve the one you are reading around.

Hc Connector M/F (1) Available Only From

This is the Male/Female Traxxas Connectors Plugs Just (No Wires).

FUNCTIONS:
Shrouded wire connections (no shrink tube required)
Wide area, gold-plated terminals
Reverse polarity security makes it impossible to connect in reverse
Textured surface area for simple gripping
Compatible with high-current 12-gauge wire
Protect, favorable locking spring loaded terminals for consistent
    contact
Multiple locking barbs keep terminals secure

INCLUDES:
One black female plastic adapter
One black male plastic adapter
2 sets of gold metal pins
Direction sheet

REQUIRES:
Soldering wires to the metal pins

The listed below item likewise sets truly well with the item being gone over.

Mounting Plate For Stampede Esc

This is the ESC and Receiver Box Mounting Plate for usage on the
Traxxas Stampede.

FEATURES:
Nylon construction
Black in color

INCLUDES:
One Mounting Plate
Four 3x7.5mm Flanged Button Head Screws
2 3x12mm Flanged Button Head Screws

REQUIRES:
Installation on the automobile

SPECS:
Length: 87mm (3.4")
Width: 60mm (2.4")
Height: 10mm (0.39")

This is a superb addition to the item currently being gone over.

Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are situated in the front steering blocks.

FEATURES:
Steel construction
Natural color

INCLUDES:
2 front axles

REQUIRES:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Size: 5mm

COMMENTS:
These will not work for the nitro variations. For that axle, usage
    TRAC2536.

This item is frequently purchased with the above discussed item.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel construction

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on automobile

This item compliments the main item here.

30T Idler Gear Steel

This is the optional Steel Idler Gear for many Traxxas Vehicles.

FEATURES:
Steel construction

INCLUDES:
One steel 30T idler equipment

REQUIRES:
Installation on automobile

Numerous others have purchased this item in addition to the item that you are currently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.