Traxxas Battery Hold-Downs, Tall (2) (Allows For Installation Of Taller

This is the Battery Hold-downs and Tall Retainers
for the Traxxas 1/10 Rally VXL rally car

FEATURES:
Made from black plastic.

INCLUDES:
One battery hold-down
One tall front hold-down retainer
One tall rear hold-down retainer

SPECIFICATIONS:
hold-down, length: 7-5/8" (194mm)
width: 1-1/4" (32mm)
height: 3/8" (10mm)
front retainer, length: 46mm (1-13/16")
width: 50mm (2")
density: 8.5mm (5/16")
rear retainer, length: 48mm (1-7/8")
width: 42mm (1-5/8")
density: 17mm (11/16")

REMARKS:
The tall hold-down retainers allow for the use of taller,
multi-cell batteries.

Often gotten with the thing that you are currently reviewing.



This is the DuraTrax Onyx 11.1V 5000mAh 25C Soft Case LiPo Battery
with the Traxxas Plug.

FEATURES:
Perfect for 1/10 scale car applications
Prewired with Traxxas high existing port

INCLUDES:
11.1V 5000mAh 25C Soft Case LiPo Battery with Traxxas High Current
    Adapter

REQUIRES:
Balancer and LiPo compatible battery charger or LiPo battery charger with built-in
    balancer such as the Onyx 235, DTXP4235

SPECIFICATIONS:
Voltage Rating: 11.1V
Ranked Capability: 5000mAh
Release Rating: 25C constant
Dimensions: 1.7 x 1.2 x 5.4" (43 x 31 x 137mm)
Weight: 13.5oz (383g)
Discharge Lead/Connectors: 12AWG Wires, Traxxas Plug
Stabilizing Adapter: ElectriFly
Watt Hours: 56Wh

REMARKS:
ALWAYS utilize a LiPo-approved Battery charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER EVER Trickle Charge
NEVER enable to Release below 2.5V per cell
NEVER disassemble or modify pack electrical wiring in any method or puncture cells
NEVER put on combustible products or leave unattended during
    charging
ALWAYS Charge in a fireproof area
ALWAYS set battery charger's output volts to match battery volts
CONSTANTLY keep out of reach of children
All weights consist of wire leads and plugs
All weights +/- 1 g
All measurements +/- 1 mm

This thing is frequently gotten with the above discussed thing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

This is a superb addition to the thing currently being gone over.

Front Or Rear A-Arms For Traxxas Slash 4X4 Or Rustler 4X4, Blue

These are the optional RPM Heavy Duty Front/Rear A-Arms
for the Traxxas Slash 4x4.

FEATURES:
Blue in color
Plastic constrution

INCLUDES:
(2) Front/Rear A-Arms

REQUIRES:
Setup on front or rear suspension

SPECIFICATIONS:
Length: 3.96" (100.5mm)
Width: 1.79" (45.5mm) at best point
Thickness: 0.31" (8mm)

REMARKS:
Also available in Black (RPMC0702)

The below thing likewise sets truly well with the thing being gone over.

Hc Connector M (2) Available Only From

These are the Male Traxxas Connectors Plugs only (No Wires).

FEATURES:
Shrouded wire connections (no shrink tube needed)
Wide surface area, gold-plated terminals
Reverse polarity security makes it difficult to connect backwards
Textured surface for simple gripping
Compatible with high-current 12-gauge wire
Safe and secure positive locking spring loaded terminals for consistent
    contact
Numerous locking barbs keep terminals protect

INCLUDES:
Two black male plastic ports
Two sets of gold metal pins
Direction sheet

REQUIRES:
Soldering wires to the metal pins