Traxxas Alum Bearing Adapter Slash 4X4

This is an optional Bearing Adapter for the Slash 4X4.

FUNCTIONS:
6061-T6 anodized blue aluminum building
Steel 10x15x4mm ball bearing with blue rubber seal
Used on slipper shaft

CONSISTS OF:
One aluminum adapter
One 10x15x4mm ball bearing

NEEDS:
Installation on to slipper shaft
Remaining clutch pieces

Below is an additional item that compliments the item being reviewed.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Equipment
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Nylon building
Black in color
.8 Module pitch

CONSISTS OF:
One 54T 0.8 Pitch Spur Equipment

NEEDS:
Assembly onto vehicle

You will love this product if you have the product just above discussed.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

This item compliments the above reviewed item.

Slipper Clutch Complete Stampede 4X4

This is the Total Slipper Clutch Set for the Slash 4X4 from Traxxas.

FEATURES:
Total slipper clutch assembly
Pre-assembled

CONSISTS OF:
2 nuts
1 spring
1 metal plate
1 pin
3 pads
2 washers
54T spur equipment

NEEDS:
Installation in vehicle

Many others have actually purchased this item together with the item that you are presently reviewing.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Set for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building

CONSISTS OF:
One Steel Disc
Two Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

NEEDS:
Disassembly of slipper clutch

Below is an additional item that compliments the item being reviewed.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Construction
Protected with blue rubber seals

CONSISTS OF:
2 Ball Bearings

NEEDS:
Assembly to vehicle

SPECIFICATIONS:
Inner Size: 10mm
Outer Size: 15mm
Side Thickness: 4mm

REMARKS:
These bearings are used to support the Primary Clutch (one required).

This is a fantastic enhancement to the item presently being reviewed.

Rebuild Kit Hd Slipper Clutch

This is the Sturdy Slipper Clutch Rebuild Set from Traxxas.

FEATURES:
Components for both nitro and electric Revo and Maxx trucks

CONSISTS OF:
Two Pads, steel Slipper Disc, two Locknuts, 2x9.8mm Pin, two
    Locknuts, Spring, two Spring Washers and Instructions

NEEDS:
Disassembly of slipper clutch

This item compliments the main item below.

Diff Carrier / X-Ring Gaskets (2) / Ring Gear Gask Et/ 6 X 1

This is the Diff Carrier/Gasket Set for the Traxxas Revo.

FEATURES:
Plastic Diff Carrier
Blue Rubber Shaft Gaskets
Black Rubber Diff Carrier Gaskets
Gray Washer

CONSISTS OF:
One Diff Carrier
2 Blue Rubber Shaft Gaskets
One Black Rubber Diff Carrier Gaskets
One Gray Washer

NEEDS:
Assembly to vehicle

You will love this product if you have the product just above discussed.

Input Shaft (Slipper Shaft)/ B

This is the Input Shaft for use on the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building
Black in color

CONSISTS OF:
One Input Shaft
One Bearing Adapter
One Pin

NEEDS:
Installation on the vehicle

SPECIFICATIONS:
Length: 58mm (2.3")

Below is an additional item that compliments the item being reviewed.



This is the Rebuild Set for the Traxxas Velineon
3500 Brushless motor - TRAC3351.

FEATURES:
Improves performance of an old motor
Detailed instruction sheet guides you through the procedure

CONSISTS OF:
2 5 x 11 x 5mm Bearings
One 5 x 7 x 13mm Brass Bushing
One 5 x 7 x 5.6mm Brass Bushing
Four 2.5 x 5mm Button Head Screws (1.5mm hex size)

NEEDS:
Removal of old parts and setup of new parts following the
consisted of instruction sheet

REMARKS:
For the replacement motor rotor order TRAC3353
For the replacement motor cover endbell order TRAC3354