Traxxas 3 X 6Mm Cap Hex Screws (6)

These are 3x5mm Backplate screws for the Traxxas 2.5 Engine.

FEATURES:
Black steel construction.

INCLUDES:
Six black steel cap head screws.

REQUIRES:
Assembly on coverplate.

SPECS:
Length: 5mm
Diameter: 3mm

COMMENTS:
These might also be described as coverplate screws.

Often gotten with the thing that you are currently checking out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

The below thing also sets really well with the thing being discussed.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Hub
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Pot Metal Construction
Silver in Color

CONSISTS OF:
One Slipper Press Plate
One Slipper Press Plate Hub

NEEDS:
Assembly onto Vehicle

This is a superb addition to the thing currently being discussed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Kit for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One Steel Disc
3 Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Guidelines

NEEDS:
Disassembly of slipper clutch

Many others have gotten this thing together with the thing that you are currently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

Below is a terrific thing that many others have purchased the same time.

Slipper Pressure Plate & Hub Revo

This is a Replacement Slipper Pressure Plate and Slipper Hub for the Revo.
These are part of the slipper assembly.

FEATURES:
Aluminum construction

CONSISTS OF:
One slipper pressure plate
One slipper hub

NEEDS:
Installation onto car.

You will certainly like this product if you have the product just above mentioned.

Rebuild Kit Hd Slipper Clutch

This is the Sturdy Slipper Clutch Rebuild Kit from Traxxas.

FEATURES:
Components for both nitro and electrical Revo and Maxx trucks

CONSISTS OF:
3 Pads, steel Slipper Disc, 2 Locknuts, 2x9.8mm Pin, 2
    Locknuts, Spring, 2 Spring Washers and Recommendations

NEEDS:
Disassembly of slipper clutch

This thing is frequently gotten with the above stated thing.

Spur Gear (90T) 48P

This is a Traxxas 48P, 90T Spur Gear for designs
with Torque Control Slipper Clutch.

FEATURES:
48 pitch
90 tooth
Created for designs with a slipper clutch
Black plastic construction

CONSISTS OF:
One spur gear

SPECS:
Pitch: 48
Tooth: 90

COMMENTS:
For this slipper clutch design there is also a 76T gear (TRAC4676),
    83T gear (TRAC4683) and 86T gear (TRAC4686).

Often gotten with the thing that you are currently checking out.

3X8mm Screws Flat-Head (Hex Drive) (6)

These are the Traxxas Flathead 3 x 8mm Screws.

FEATURES:
Metal construction
Black in color

CONSISTS OF:
Six 3 x 8mm Flathead Hex Screws

NEEDS:
Installation on the car

This is a superb addition to the thing currently being discussed.

3 X 8Mm Counter Hex Screw (6)

These are 3x8mm Countersunk Hex Head Screws by Traxxas.
Can be used anywhere this kind of screw is needed.

FEATURES:
Metal Construction
Black in Color
Countersunk

CONSISTS OF:
(6) Screws

SPECS:
Length: 8mm
Diameter: 3mm