Traxxas 54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Nylon construction
Black in color
.8 Module pitch

INCLUDES:
One 54T 0.8 Pitch Spur Gear

NEEDS:
Assembly onto vehicle

Many others have gotten this thing together with the thing that you are currently reviewing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Here is a great thing that several others have purchased the exact same time.

Alum Bearing Adapter Slash 4X4

This is an optional Bearing Adapter for the Slash 4X4.

FEATURES:
6061-T6 anodized blue aluminum construction
Steel 10x15x4mm ball bearing with blue rubber seal
Utilized on slipper shaft

INCLUDES:
One aluminum adapter
One 10x15x4mm ball bearing

NEEDS:
Setup on to slipper shaft
Remaining clutch pieces

You will like this item if you have the item earlier pointed out.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for usage on the Traxxas Revo.

FEATURES:
Steel Building and construction
Protected with blue rubber seals

INCLUDES:
2 Ball Bearings

NEEDS:
Assembly to vehicle

SPECS:
Inner Size: 10mm
Outer Size: 15mm
Side Density: 4mm

REMARKS:
These bearings are utilized to support the Main Clutch (one required).

This thing compliments the above gone over thing.

13T Pinion Gear 32P

This is a 13 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the equipment which is connected straight to the motor.

FEATURES:
Machined Steel
Developed for a 3mm shaft

INCLUDES:
One 13 tooth Pinion Gear
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This equipment is just one of 2 which are utilized on the E-Maxx double motor
    set-up.

This thing compliments the above gone over thing.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Package for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction

INCLUDES:
One Steel Disc
3 Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

NEEDS:
Disassembly of slipper clutch

This is a fantastic addition to the thing currently being gone over.

Input Shaft (Slipper Shaft)/ B

This is the Input Shaft for usage on the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction
Black in color

INCLUDES:
One Input Shaft
One Bearing Adapter
One Pin

NEEDS:
Setup on the vehicle

SPECS:
Length: 58mm (2.3")

Here is one more thing that compliments the thing being gone over.

Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FEATURES:
Totally assembled
Plastic telescoping driveshaft with steel universals
Blue rubber boot guards telescoping areas from dirt
Attaches to the differential with one screw pin
Works on the front or rear, right or left of vehicle

INCLUDES:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Instruction sheet

NEEDS:
Installing on chassis