Traxxas 54T 0.8 P Spur Gear

This is the 54 Tooth Spur Equipment
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Nylon construction
Black in color
.8 Module pitch

INCLUDES:
One 54T 0.8 Pitch Spur Equipment

REQUIRES:
Assembly onto automobile

Lots of others have acquired this item in addition to the item that you are presently checking out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Right here is a terrific item that several others have bought at the same time.

Alum Bearing Adapter Slash 4X4

This is an optional Bearing Adapter for the Slash 4X4.

FUNCTIONS:
6061-T6 anodized blue aluminum construction
Steel 10x15x4mm ball bearing with blue rubber seal
Used on slipper shaft

INCLUDES:
One aluminum adapter
One 10x15x4mm ball bearing

REQUIRES:
Setup on to slipper shaft
Remaining clutch pieces

You will love this product if you have the product above discussed.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building and construction
Shielded with blue rubber seals

INCLUDES:
2 Ball Bearings

REQUIRES:
Assembly to automobile

SPECIFICATIONS:
Inner Size: 10mm
Outer Size: 15mm
Side Thickness: 4mm

REMARKS:
These bearings are used to support the Main Clutch (one required).

This item compliments the above gone over item.

13T Pinion Gear 32P

This is a 13 Tooth 32 Pitch Pinion Equipment for the Traxxas E-Maxx Truck.
This is the equipment which is connected straight to the motor.

FEATURES:
Machined Steel
Developed for a 3mm shaft

INCLUDES:
One 13 tooth Pinion Equipment
One 3 x 4mm Set Screw

REQUIRES:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This equipment is just one of 2 which are used on the E-Maxx double motor
    set-up.

This item compliments the above gone over item.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Package for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction

INCLUDES:
One Steel Disc
Three Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Instructions

REQUIRES:
Disassembly of slipper clutch

This is a great addition to the item presently being gone over.

Input Shaft (Slipper Shaft)/ B

This is the Input Shaft for use on the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction
Black in color

INCLUDES:
One Input Shaft
One Bearing Adapter
One Pin

REQUIRES:
Setup on the automobile

SPECIFICATIONS:
Length: 58mm (2.3")

Right here is one more item that compliments the item being gone over.

Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FUNCTIONS:
Totally assembled
Plastic telescoping driveshaft with steel universals
Blue rubber boot shields telescoping sections from dirt
Attaches to the differential with one screw pin
Works on the front or back, right or left of automobile

INCLUDES:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Guideline sheet

REQUIRES:
Setting up on chassis