Traxxas 4Mm Flanged Nylock Nuts (8)

This is the Traxxas Flanged Nylon Locking Nuts.

FEATURES:
Steel serrated building

INCLUDES:
Eiqht 4mm flanged nylon locking nuts

SPECS:
Outside size: 7mm

Right here is an additional product that praises the product being talked about.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that link the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

This product is frequently acquired with the above pointed out product.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Right here is a terrific product that lots of others have purchased the exact same time.

Maxx Series Body Clips 12Pc

These are the Body Clips for the Traxxas E-Maxx and T-Maxx Trucks.

FEATURES:
Steel building
Natural sleek color

INCLUDES:
Twelve Body Clips

SPECS:
Length: 26mm

The below product likewise sets really well with the product being talked about.

Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel building
Natural color

INCLUDES:
2 front axles

REQUIRES:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Size: 5mm

COMMENTS:
These will not work for the nitro variations. For that axle, usage
    TRAC2536.

Right here is a terrific product that lots of others have purchased the exact same time.

Caster Blocks 30 Degree (L&R) Slash / Stampede / Rustler

These are Castor Blocks for the Traxxas
Rustler and Stampede.

FEATURES:
Black Plastic Construction

INCLUDES:
2 Blocks

REQUIRES:
Traxxas Rustler or Stampede

Lots of others have acquired this product in addition to the product that you are presently reviewing.

Front Bearing Carriers, For Slash 2Wd, Nitro Slash, E-Rustler &

These are Optional Front Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Bandit

The Front axles fit into these bearing carriers.

FEATURES:
Black nylon building

INCLUDES:
2 Front bearing (center) carriers
2 RPM decals

REQUIRES:
(4) 5x11mm bearings, if needed usage (2) DTXC1547.

Right here is a terrific product that lots of others have purchased the exact same time.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These obstructs install to the front A-arms and is what the
steering knuckles connect to.

FEATURES:
Nylon building, black in color
Stamped right and left to insure correct setup

INCLUDES:
2 RPM 30° Front Caster Blocks

REQUIRES:
Assembly in between A-arms and steering knuckles

You will like this item if you have the item above discussed.

Susp Screw Pin Set #2640 (Hex Drive)

These are the Suspension Screws Pins for the
Traxxas Rustler, Stampede and Bandit.
The hinge pins hold the suspension arms to the bulkheads

FEATURES:
Resilient steel building

INCLUDES:
2 48mm pins
2 34mm pins
2 30mm pins
2 28mm pins
2 25mm pins

REQUIRES:
Setup on the Rustler, Stampede or Bandit

COMMENTS:
For a complete suspension pin set order TRAC4940

You will like this item if you have the item above discussed.

Suspension King Pin 2.5X31.5

This is the Traxxas (TRA) #3740 2.5x31.5mm Pins with E-clips.

FEATURES:
Made of stainless-steel
This is used to hold the front steering block (TRAC9036 #3636)
to the castor block (TRAC9032 #3632) on the electrical
(not Nitro) Rustler
Also called the vertical kingpin

INCLUDES:
2 Pins (kingpins)
4 2.5mm e-clips

AXY
9/22/97