Traxxas 5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

Get this thing to enhance the one you are reading around.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for usage on the Traxxas Revo.

FEATURES:
Steel Construction
Protected with blue rubber seals

CONSISTS OF:
2 Ball Bearings

NEEDS:
Assembly to automobile

SPECIFICATIONS:
Inner Size: 10mm
Outer Size: 15mm
Side Thickness: 4mm

COMMENTS:
These bearings are utilized to support the Primary Clutch (one required).

Regularly purchased with the thing that you are currently reading about.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Thickness: 0.5mm

Regularly purchased with the thing that you are currently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

This is a amazing addition to the thing currently being discussed.

Front Bearing Carriers, For Slash 2Wd, Nitro Slash, E-Rustler &

These are Optional Front Bearing Providers for the Traxxas Electric
Rustler, Stampede and Bandit

The Front axles suit these bearing carriers.

FEATURES:
Black nylon construction

CONSISTS OF:
2 Front bearing (hub) providers
2 RPM decals

NEEDS:
(4) 5x11mm bearings, if required usage (2) DTXC1547.

This is a amazing addition to the thing currently being discussed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Installation on automobile

You will like this item if you have the item previously discussed.

30T Idler Gear Steel

This is the optional Steel Idler Gear for many Traxxas Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One steel 30T idler equipment

NEEDS:
Installation on automobile

This thing praises the main item below.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel leading drive equipment that fits several Traxxas
cars. .
Includes: 1 equipment only

You will like this item if you have the item previously discussed.

Rear Bearing Carriers, For Traxxas Slash 2Wd, E-Rustler, E-Stamp

These are Optional Back Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Bandit.
The rear axles suit these bearing carriers.

FEATURES:
Black nylon construction

CONSISTS OF:
2 rear bearing (hub) providers
2 RPM decals

NEEDS:
(4) 5x11mm bearings, if required usage (2) DTXC1547.

SPECS:
Height: 40mm (1.58")
Width at widest point: 15.4mm (0.61")

You will like this item if you have the item previously discussed.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Total Planetary Gear Differential With Steel Ring Gear
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal equipment shafts
Metal and plastic primary differential

CONSISTS OF:
Main differential with steel ring equipment
Planetary gears and shafts
Sun gears and shafts
Silicone grease

NEEDS:
Installation on the automobile

COMMENTS:
For primary differential w/ steel ring - TRAC6380
World equipment shafts - TRAC6382
Silicon grease _- TRAC6037