Traxxas 5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Get this item to improve the one you are reading about.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for usage on the Traxxas Revo.

FEATURES:
Steel Building
Protected with blue rubber seals

CONSISTS OF:
Two Ball Bearings

NEEDS:
Assembly to vehicle

SPECIFICATIONS:
Inner Size: 10mm
Outer Size: 15mm
Side Thickness: 4mm

COMMENTS:
These bearings are used to support the Primary Clutch (one required).

Regularly bought with the item that you are currently reviewing.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Thickness: 0.5mm

Regularly bought with the item that you are currently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

This is a fantastic addition to the item currently being reviewed.

Front Bearing Carriers, For Slash 2Wd, Nitro Slash, E-Rustler &

These are Optional Front Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Outlaw

The Front axles suit these bearing carriers.

FEATURES:
Black nylon building

CONSISTS OF:
Two Front bearing (center) carriers
Two RPM decals

NEEDS:
(4) 5x11mm bearings, if required usage (2) DTXC1547.

This is a fantastic addition to the item currently being reviewed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on vehicle

You will certainly enjoy this product if you have the product previously mentioned.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for numerous Traxxas Vehicles.

FEATURES:
Steel building

CONSISTS OF:
One steel 30T idler equipment

NEEDS:
Setup on vehicle

This item compliments the main item right here.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel leading drive equipment that fits several Traxxas
vehicles. .
Consists of: 1 equipment only

You will certainly enjoy this product if you have the product previously mentioned.

Rear Bearing Carriers, For Traxxas Slash 2Wd, E-Rustler, E-Stamp

These are Optional Rear Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Bandit.
The rear axles suit these bearing carriers.

FEATURES:
Black nylon building

CONSISTS OF:
Two rear bearing (center) carriers
Two RPM decals

NEEDS:
(4) 5x11mm bearings, if required usage (2) DTXC1547.

SPECS:
Height: 40mm (1.58")
Width at best point: 15.4mm (0.61")

You will certainly enjoy this product if you have the product previously mentioned.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Complete Planetary Equipment Differential With Steel Ring Equipment
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal equipment shafts
Metal and plastic main differential

CONSISTS OF:
Main differential with steel ring equipment
Planetary gears and shafts
Sun gears and shafts
Silicone grease

NEEDS:
Setup on the vehicle

COMMENTS:
For main differential w/ steel ring - TRAC6380
World equipment shafts - TRAC6382
Silicon grease _- TRAC6037