Traxxas 5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Get this thing to boost the one you read around.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for usage on the Traxxas Revo.

FEATURES:
Steel Building and construction
Protected with blue rubber seals

CONSISTS OF:
2 Ball Bearings

NEEDS:
Assembly to vehicle

SPECS:
Inner Diameter: 10mm
Outer Diameter: 15mm
Side Density: 4mm

COMMENTS:
These bearings are used to support the Main Clutch (one needed).

Frequently bought with the thing that you are currently checking out.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Density: 0.5mm

Frequently bought with the thing that you are currently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

This is a superb enhancement to the thing currently being reviewed.

Front Bearing Carriers, For Slash 2Wd, Nitro Slash, E-Rustler &

These are Optional Front Bearing Providers for the Traxxas Electric
Rustler, Stampede and Outlaw

The Front axles suit these bearing carriers.

FEATURES:
Black nylon building and construction

CONSISTS OF:
2 Front bearing (hub) providers
2 RPM decals

NEEDS:
(4) 5x11mm bearings, if needed usage (2) DTXC1547.

This is a superb enhancement to the thing currently being reviewed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building and construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on vehicle

You will love this item if you have the item just above stated.

30T Idler Gear Steel

This is the optional Steel Idler Gear for lots of Traxxas Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One steel 30T idler equipment

NEEDS:
Setup on vehicle

This thing praises the main item below.

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel leading drive equipment that fits numerous Traxxas
cars. .
Includes: 1 equipment just

You will love this item if you have the item just above stated.

Rear Bearing Carriers, For Traxxas Slash 2Wd, E-Rustler, E-Stamp

These are Optional Rear Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Bandit.
The rear axles suit these bearing carriers.

FEATURES:
Black nylon building and construction

CONSISTS OF:
2 rear bearing (hub) providers
2 RPM decals

NEEDS:
(4) 5x11mm bearings, if needed usage (2) DTXC1547.

SPECS:
Height: 40mm (1.58")
Width at widest point: 15.4mm (0.61")

You will love this item if you have the item just above stated.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Total Planetary Gear Differential With Steel Ring Gear
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal equipment shafts
Metal and plastic primary differential

CONSISTS OF:
Main differential with steel ring equipment
Planetary gears and shafts
Sun gears and shafts
Silicone grease

NEEDS:
Setup on the vehicle

COMMENTS:
For primary differential w/ steel ring - TRAC6380
Planet equipment shafts - TRAC6382
Silicon grease _- TRAC6037