Traxxas 5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Get this thing to enhance the one you read around.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building
Protected with blue rubber seals

CONSISTS OF:
2 Ball Bearings

REQUIRES:
Assembly to car

SPECIFICATIONS:
Inner Size: 10mm
Outer Size: 15mm
Side Thickness: 4mm

COMMENTS:
These bearings are used to support the Main Clutch (one needed).

Often purchased with the thing that you are presently checking out.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Thickness: 0.5mm

Often purchased with the thing that you are presently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

This is a great addition to the thing presently being talked about.

Front Bearing Carriers, For Slash 2Wd, Nitro Slash, E-Rustler &

These are Optional Front Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Outlaw

The Front axles suit these bearing carriers.

FEATURES:
Black nylon construction

CONSISTS OF:
2 Front bearing (center) carriers
2 RPM decals

REQUIRES:
(4) 5x11mm bearings, if needed use (2) DTXC1547.

This is a great addition to the thing presently being talked about.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on car

You will certainly like this thing if you have the thing previously pointed out.

30T Idler Gear Steel

This is the optional Steel Idler Gear for lots of Traxxas Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One steel 30T idler gear

REQUIRES:
Installation on car

This thing compliments the main item here.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel top drive gear that fits numerous Traxxas
cars. .
Consists of: 1 gear only

You will certainly like this thing if you have the thing previously pointed out.

Rear Bearing Carriers, For Traxxas Slash 2Wd, E-Rustler, E-Stamp

These are Optional Back Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Bandit.
The rear axles suit these bearing carriers.

FEATURES:
Black nylon construction

CONSISTS OF:
2 rear bearing (center) carriers
2 RPM decals

REQUIRES:
(4) 5x11mm bearings, if needed use (2) DTXC1547.

SPECS:
Height: 40mm (1.58")
Width at best point: 15.4mm (0.61")

You will certainly like this thing if you have the thing previously pointed out.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Complete Planetary Gear Differential With Steel Ring Gear
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal gear shafts
Metal and plastic primary differential

CONSISTS OF:
Main differential with steel ring gear
Planetary equipments and shafts
Sun equipments and shafts
Silicone grease

REQUIRES:
Installation on the car

COMMENTS:
For primary differential w/ steel ring - TRAC6380
World gear shafts - TRAC6382
Silicon grease _- TRAC6037