Traxxas 5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

Get this product to enhance the one you are reading about.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building
Shielded with blue rubber seals

CONSISTS OF:
Two Ball Bearings

NEEDS:
Assembly to car

SPECS:
Inner Diameter: 10mm
External Diameter: 15mm
Side Thickness: 4mm

COMMENTS:
These bearings are utilized to support the Main Clutch (one needed).

Regularly gotten with the product that you are presently checking out.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Thickness: 0.5mm

Regularly gotten with the product that you are presently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

This is a great addition to the product presently being talked about.

Front Bearing Carriers, For Slash 2Wd, Nitro Slash, E-Rustler &

These are Optional Front Bearing Providers for the Traxxas Electric
Rustler, Stampede and Bandit

The Front axles suit these bearing carriers.

FEATURES:
Black nylon building

CONSISTS OF:
Two Front bearing (hub) carriers
Two RPM decals

NEEDS:
(4) 5x11mm bearings, if needed use (2) DTXC1547.

This is a great addition to the product presently being talked about.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on car

You will like this item if you have the item just above pointed out.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for numerous Traxxas Vehicles.

FEATURES:
Steel building

CONSISTS OF:
One steel 30T idler equipment

NEEDS:
Setup on car

This product praises the main item below.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel top drive equipment that fits several Traxxas
cars. .
Consists of: 1 equipment only

You will like this item if you have the item just above pointed out.

Rear Bearing Carriers, For Traxxas Slash 2Wd, E-Rustler, E-Stamp

These are Optional Rear Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Bandit.
The rear axles suit these bearing carriers.

FEATURES:
Black nylon building

CONSISTS OF:
Two rear bearing (hub) carriers
Two RPM decals

NEEDS:
(4) 5x11mm bearings, if needed use (2) DTXC1547.

SPECS:
Height: 40mm (1.58")
Width at best point: 15.4mm (0.61")

You will like this item if you have the item just above pointed out.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Complete Planetary Equipment Differential With Steel Ring Equipment
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal equipment shafts
Metal and plastic main differential

CONSISTS OF:
Main differential with steel ring equipment
Planetary gears and shafts
Sun gears and shafts
Silicone grease

NEEDS:
Setup on the car

COMMENTS:
For main differential w/ steel ring - TRAC6380
Planet equipment shafts - TRAC6382
Silicon grease _- TRAC6037