Traxxas 30T Idler Gear Steel

This is the optional Steel Idler Gear for many Traxxas Vehicles.

FEATURES:
Steel building

SUCHES AS:
One steel 30T idler gear

REQUIRES:
Installation on car

You will certainly enjoy this item if you have the item previously mentioned.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

SUCHES AS:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

This item praises the main item right here.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel leading drive gear that fits several Traxxas
automobiles. .
Includes: 1 gear only

Many others have bought this item along with the item that you are presently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

SUCHES AS:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

Many others have bought this item along with the item that you are presently reading about.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Total Planetary Gear Differential With Steel Ring Gear
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal gear shafts
Metal and plastic primary differential

SUCHES AS:
Main differential with steel ring gear
Planetary gears and shafts
Sun gears and shafts
Silicone grease

REQUIRES:
Installation on the car

COMMENTS:
For primary differential w/ steel ring - TRAC6380
Planet gear shafts - TRAC6382
Silicon grease _- TRAC6037

Below is a terrific item that several others have bought at the exact same time.

Main Diff W/ Steel Ring Gear/ Side Cover Plate/ Sc Rews (Ban

This is the Main Diff with Steel Ring Gear from Traxxas
for the Bandit, Stampede and Rustler VXL series.

Includes: Main diff with steel ring gear
Side cover plate
Screws
Directions

Requires: Installation on the car

Want an additional terrific item to match the above discussed item?

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Below is an additional item that praises the item being reviewed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building

SUCHES AS:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on car

Want an additional terrific item to match the above discussed item?

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building
Steel idler shaft

SUCHES AS:
One gearbox
One idler shaft

COMMENTS:
This part fit the standard and XL version of both the Stampede
and Rustler.

You will certainly enjoy this item if you have the item previously mentioned.

Front Axles (2) (R & S)

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede.
These lie in the front steering blocks.

FEATURES:
Steel building
Natural color

SUCHES AS:
Two front axles

REQUIRES:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Size: 5mm

COMMENTS:
These will not work for the nitro versions. For that axle, usage
    TRAC2536.