Traxxas 13T Pinion Gear 32P

This is a 13 Tooth 32 Pitch Pinion Equipment for the Traxxas E-Maxx Truck.
This is the equipment which is attached directly to the motor.

FEATURES:
Machined Steel
Created for a 3mm shaft

INCLUDES:
One 13 tooth Pinion Equipment
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten set screw.

COMMENTS:
This equipment is only one of two which are utilized on the E-Maxx double motor
    set-up.

This item praises the above gone over item.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Equipment
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Nylon building and construction
Black in color
.8 Module pitch

INCLUDES:
One 54T 0.8 Pitch Spur Equipment

NEEDS:
Assembly onto car

This item praises the main item below.

14T Pinion Gear 32P

This is a 14 Tooth 32 Pitch Pinion Equipment for the Traxxas E-Maxx Truck.
This is the equipment which is attached directly to the motor.

FEATURES:
Machined Steel
Created for a 3mm shaft

INCLUDES:
One 14 tooth Pinion Equipment
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten set screw.

COMMENTS:
This equipment is only one of two which are utilized on the E-Maxx double motor
    set-up.

This is a wonderful addition to the item presently being gone over.

12T Pinion Gear 32P

This is a 12 Tooth 32 Pitch Pinion Equipment for the Traxxas E-Maxx Truck.
This is the equipment which is attached directly to the motor.

FEATURES:
Machined Steel
Created for a 3mm shaft

INCLUDES:
One 12 tooth Pinion Equipment
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten set screw.

COMMENTS:
This equipment is only one of two which are utilized on the E-Maxx double motor
    set-up.

Below is an additional item that praises the item being gone over.

Hc Connector M (2) Available Only From

These are the Male Traxxas Connectors Plugs only (No Wires).

FEATURES:
Shrouded wire connections (no diminish tube needed)
Wide surface location, gold-plated terminals
Reverse polarity defense makes it difficult to link in reverse
Textured surface for simple gripping
Suitable with high-current 12-gauge wire
Protected favorable locking spring crammed terminals for constant
    contact
Several locking barbs keep terminals protect

INCLUDES:
2 black male plastic connectors
2 sets of gold metal pins
Instruction sheet

NEEDS:
Soldering wires to the metal pins

You will certainly love this item if you have the item above mentioned.



This is the DuraTrax Onyx 7.4V 5000mAh 25C Hard Case LiPo Battery
with the Traxxas Plug.

FEATURES:
Ideal for 1/10 scale car applications
Prewired with Traxxas high current adapter

INCLUDES:
7.4V 5000mAh 25C Difficult Case LiPo Battery with Traxxas Plug

NEEDS:
Balancer and LiPo suitable charger or LiPo charger with built-in
    balancer such as the Onyx 235, DTXP4235

SPECS:
Voltage Rating: 7.4V
Rated Capacity: 5000mAh
Release Rating: 25C constant
Dimensions: 1.77 x .94 x 5.4" (45 x 24 x 137mm)
Weight: 10.2oz (288g)
Discharge Lead/Connectors: 12AWG Wires, Traxxas Plug
Stabilizing Adapter: ElectriFly
Watt Hours: 37Wh

COMMENTS:
ALWAYS use a LiPo-approved Battery charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER Trickle Charge
NEVER permit to Release listed below 2.5V per cell
NEVER dismantle or modify pack circuitry in any method or leak cells
NEVER place on flammable products or leave unattended throughout
    charging
ALWAYS Charge in a fire-resistant place
ALWAYS set charger's output volts to match battery volts
ALWAYS shut out of reach of children
All weights include wire leads and plugs
All weights +/- 1 g