RPM Caster Blocks & Spindle Blocks For The Slash 4X4, Stampede 4X4,

These are the optional RPM Caster and Steering Blocks for all variations of the
Traxxas Slash 4x4, Stampede 4x4 and the 1/10 scale Rally 4WD.

FUNCTIONS:
Plastic building

INCLUDES:
2 Caster Blocks and two Guiding Blocks

Lots of others have actually acquired this product in addition to the product that you are presently checking out.

Rear Bearing Carrier For Traxxas Slash 4X4 Or Rustler 4X4, Black

These are optional Back Bearing Carriers for the Traxxas Slash 4x4, Nitro
Rustler, Nitro Stampede, Nitro Sport, Rad2, Hawk 2 and Eagle/Eagle LSII.

FEATURES:
Nylon building
Black in color

INCLUDES:
2 Back Bearing Carriers
Decal

NEEDS:
2 5x11x4mm ball bearings, DTXC1547

Lots of others have actually acquired this product in addition to the product that you are presently checking out.

Front Or Rear A-Arms For Traxxas Slash 4X4 Or Rustler 4X4, Red

These are the optional RPM Heavy Duty Front or Rear A-Arms in Red
for the Traxxas Slash 4x4, and Stampede 4x4.

FUNCTIONS:
Each A-arm is 0.22oz (6.5g) lighter than stock A-arm
Removes slop in suspension and tightens up tolerances around hinge
    pins
Decreased fore and aft motion at inner hinge pin and axle providers
    by higher than 90%
Nylon blend building, red in color

INCLUDES:
Left and Right Front or Rear A-Arms (two packages required to
    complete one truck

This is a great addition to the product presently being discussed.

Slipper Pressure Plate & Hub Revo

This is a Replacement Slipper Pressure Plate and Slipper Center for the Revo.
These are part of the slipper assembly.

FEATURES:
Aluminum building

INCLUDES:
One slipper pressure plate
One slipper center

NEEDS:
Setup onto automobile.

Here is an additional product that compliments the product being discussed.

Rebuild Kit Hd Slipper Clutch

This is the Heavy Duty Slipper Clutch Rebuild Set from Traxxas.

FEATURES:
Elements for both nitro and electrical Revo and Maxx trucks

INCLUDES:
Three Pads, steel Slipper Disc, two Locknuts, 2x9.8mm Pin, two
    Locknuts, Spring, two Spring Washers and Instructions

NEEDS:
Disassembly of slipper clutch

This is a great addition to the product presently being discussed.

Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building

INCLUDES:
Front driveshaft assembly
Screw pin

NEEDS:
Setup on automobile

Here is a excellent product that lots of others have actually purchased the exact same time.

Alum Bearing Adapter Slash 4X4

This is an optional Bearing Adapter for the Slash 4X4.

FUNCTIONS:
6061-T6 anodized blue aluminum building
Steel 10x15x4mm ball bearing with blue rubber seal
Used on slipper shaft

INCLUDES:
One aluminum adapter
One 10x15x4mm ball bearing

NEEDS:
Setup on to slipper shaft
Remaining clutch pieces

This product compliments the above discussed product.

Front Or Rear A-Arms For Traxxas Slash 4X4 And Rustler 4X4, Blac

These are the optional RPM Heavy Duty Front/Rear A-Arms
for the Traxxas Slash 4x4.

FUNCTIONS:
Black in color
Plastic constrution

INCLUDES:
2 Front/Rear A-Arms

NEEDS:
Setup at front or rear suspension

SPECIFICATIONS:
Length: 3.96" (100.5mm)
Width: 1.79" (45.5mm) at largest point
Density: 0.31" (8mm)

REMARKS:
Likewise available in Blue (RPMC0705)