HPI Shock Shaft, 3X52mm, Bullet Mt/St (Pair)

This is the Shock Shaft 3x52mm
For the HPI Racing Bullet Series

FEATURES:
Steel building

CONSISTS OF:
Two shock shafts

COMMENTS:
This shaft can be installed on
1/10 Bullet ST Flux 2.4GHz RTR (HPID7008)
1/10 Bullet MT Flux 2.4GHz RTR (HPID7010)
1/10 Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
1/10 Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

Get this thing to improve the one you read around.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal Four Plug System enables connectivity between today's
    4 most typical battery plugs, Tamiya, Traxxas, Deans and EC3,
    just connect preferred plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Team Checkpoint Pro Automobile balancer (TCPP9150)

SPECIFICATIONS:
Configuration: TWO
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Minutes Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

COMMENTS:
READ the ENTIRE instruction sheet consisted of with battery prior to use
ALWAYS utilize a LiPo-approved Charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER EVER Trickle Charge
NEVER permit to Discharge below 2.5V per cell
NEVER take apart or modify pack electrical wiring in any method or leak cells
NEVER put on flammable products or leave ignored during
charging
ALWAYS charge in a fireproof location
ALWAYS set charger's output volts to match battery volts
ALWAYS keep out of reach of kids

Get this thing to improve the one you read around.

Slipper Clutch Spring, 7X9x1.7Mm, 3 Coils, Bullet Mt/St

This is the Slipper Clutch Spring 7x9x1.7mm 3 Coils
For the HPI Racing Bullet Series

FEATURES:
Black colored steel building

CONSISTS OF:
One spring

COMMENTS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

The below thing likewise sets actually well with the thing being discussed.

Spring, 13.5X63x1.2Mm, 11 Coils, Bullet Mt/St (2Pcs)

This is the Shock Spring 13.5x63x1.2mm 11 Coils
For the HPI Racing Bullet Series

FEATURES:
Steel building

CONSISTS OF:
Two Shock Springs

COMMENTS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)