HPI Front/Rear Upright Set Left/Right

These are the Front Knuckles and Back Uprights
for the HPI WR8 and Bullet Series of Vehicles.

FEATURES:
Plastic building

INCLUDES:
Left and Right Front Knuckles and Back Uprights with four Hex Inserts

You will certainly enjoy this thing if you have the thing just above pointed out.

Front Hub Carriers (10 Degrees), Bullet Mt/St

These are the Front Center Providers for the HPI WR8 and Bullet Series.

FEATURES:
Plastic building

INCLUDES:
Left and Right Front Center Providers

NEEDS:
Four 5x10mm Ball Bearings, DTXC1535

You will certainly enjoy this thing if you have the thing just above pointed out.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Pack with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal Four Plug System enables connectivity between today's
    four most typical battery plugs, Tamiya, Traxxas, Deans and EC3,
    just connect desired plug to Venom plug on battery's wire leads

INCLUDES:
7.4V 5000mAh 40C Hardcase LiPo Battery Pack with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Automobile balancer (TCPP9150)

SPECIFICATIONS:
Setup: 2S
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Minutes Discharge Volts Per Pack: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Pack: 8.4V

REMARKS:
READ the ENTIRE guideline sheet included with battery before use
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER EVER Trickle Charge
NEVER allow to Release below 2.5V per cell
NEVER dismantle or customize pack electrical wiring in any way or leak cells
NEVER put on flammable materials or leave unattended throughout
charging
ALWAYS charge in a fire-resistant location
ALWAYS set charger's output volts to match battery volts
CONSTANTLY stay out of reach of kids

This product compliments the main item below.

Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to secure versus dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECIFICATIONS:
Size: 5mm x 10mm

This product is frequently acquired with the above pointed out product.

Flange Locknut M4 (4)

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be used for wheels, slipper clutch springs, & other applications
    which need simple elimination and will not loosen up due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECIFICATIONS:
Diameter: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")