HPI Front/Rear Upright Set Left/Right

These are the Front Knuckles and Rear Uprights
for the HPI WR8 and Bullet Series of Vehicles.

FEATURES:
Plastic building

INCLUDES:
Left and Right Front Knuckles and Rear Uprights with 4 Hex Inserts

You will enjoy this thing if you have the thing previously stated.

Front Hub Carriers (10 Degrees), Bullet Mt/St

These are the Front Hub Providers for the HPI WR8 and Bullet Series.

FEATURES:
Plastic building

INCLUDES:
Left and Right Front Hub Providers

NEEDS:
Four 5x10mm Ball Bearings, DTXC1535

You will enjoy this thing if you have the thing previously stated.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal Four Plug System permits connectivity between today's
    4 most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    just connect preferred plug to Venom plug on battery's wire leads

INCLUDES:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if using
    Duratrax Onyx series
LiPo Balancer such as the Team Checkpoint Pro Automobile balancer (TCPP9150)

SPECIFICATIONS:
Setup: TWO
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Minutes Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

REMARKS:
CHECK OUT the ENTIRE direction sheet consisted of with battery before use
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER EVER Trickle Charge
NEVER enable to Release below 2.5V per cell
NEVER disassemble or modify pack circuitry in any way or leak cells
NEVER place on flammable products or leave unattended during
charging
ALWAYS charge in a fireproof area
ALWAYS set charger's output volts to match battery volts
ALWAYS stay out of reach of children

This product compliments the main item right here.

Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to secure against dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECIFICATIONS:
Size: 5mm x 10mm

This product is often acquired with the above stated product.

Flange Locknut M4 (4)

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be utilized for wheels, slipper clutch springs, & other applications
    which need easy elimination and will not loosen up due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECIFICATIONS:
Diameter: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")