Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Plume) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Extremely slim case and light-weight for mounting in little aircrafts,
    electrics or gliders, where really high speed and good torque are
    critical.
One of the slimmest micro servos available.
High-strength resin gear train provides reliable operation.

INCLUDES:
One HS-55 Servo w/pre-installed little X-shaped servo horn and screw
One really little straight servo horn
One M1.7x3 servo horn screw
One little straight servo horn
Two M1.7x7 servo mounting screws

at 4.8V
SPECIFICATIONS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

This thing is often purchased with the above stated thing.



This is the Futaba S3003 Standard Servo.
This fundamental servo is utilized in cars, boats, or where standard servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If using NiMH or LiPo batteries, make sure they are capable
of delivering enough amps.

INCLUDES:
One S3003 standard servo with preinstalled Xshape servo horn FUTM0031
Four brass eyelets
Four Black rectangle-shaped rubber grommets (FUTM2348)
Four servo mount screws
One servo wheel 1-3/8" (35mm) in diameter
One X-shape servo arm 1.5" (38mm) throughout
One star shaped arm 1-1/4" (32mm) throughout
Nylon gears
One year guarantee

SPECIFICATIONS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Measurements: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Adapter: "J" type with approx. 5" lead

Often purchased with the thing that you are presently reading about.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") plane propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design provides these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon building decreases turning mass for
    higher output and longer life.
Reinforcing carbon fibers help preserve true, consistent pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft locating rings
One locating ring direction sheet

REQUIRES:
ALL props require balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not designed for Glow engines

The below thing also sets truly well with the thing being discussed.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FUNCTIONS:
Light-weight molded nylon building decreases turning mass for
    higher output and longer life
Designed for electric powered Park Flyer type aircraft with rear
    facing motors that "push" the plane forward

CONSISTS OF:
8x3.8 Slo-Flyer Pusher Propeller with 2 locating rings and
    direction sheet

SPECIFICATIONS:
Length: 8" Pitch: 3.8"
Center Density: 0.30" Center diameter: 0.50"
Hole Diameter: 1/4"

REQUIRES:
Just for usage with electric motors. Not for usage with glow or gas
    engines.
All props require balancing, this is VERY important, use TOPQ5700.
May requirement prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)