Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Plume) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Really slim case and lightweight for mounting in small planes,
    electrics or gliders, where extremely high speed and excellent torque are
    critical.
One of the slimmest micro servos available.
High-strength resin gear train provides trustworthy operation.

INCLUDES:
One HS-55 Servo w/pre-installed small X-shaped servo horn and screw
One extremely small straight servo horn
One M1.7x3 servo horn screw
One small straight servo horn
2 M1.7x7 servo mounting screws

at 4.8V
SPECIFICATIONS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

This item is often gotten with the above discussed item.



This is the Futaba S3003 Requirement Servo.
This standard servo is utilized in cars, boats, or where standard servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If utilizing NiMH or LiPo batteries, make certain they are capable
of providing adequate amps.

INCLUDES:
One S3003 standard servo with preinstalled Xshape servo horn FUTM0031
Four brass eyelets
Four Black rectangle-shaped rubber grommets (FUTM2348)
Four servo mount screws
One servo wheel 1-3/8" (35mm) in size
One X-shape servo arm 1.5" (38mm) across
One star shaped arm 1-1/4" (32mm) across
Nylon gears
One year guarantee

SPECIFICATIONS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Measurements: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Port: "J" type with approx. 5" lead

Frequently gotten with the item that you are presently reviewing.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") plane propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design gives these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon building and construction lowers rotating mass for
    higher output and longer life.
Reinforcing carbon fibers assist maintain real, continuous pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of small shaft locating rings
One locating ring instruction sheet

REQUIRES:
ALL props need balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not designed for Radiance engines

The listed below item also sets actually well with the item being reviewed.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FEATURES:
Light-weight molded nylon building and construction lowers rotating mass for
    higher output and longer life
Developed for electric powered Park Leaflet type aircraft with rear
    dealing with motors that "push" the plane forward

INCLUDES:
8x3.8 Slo-Flyer Pusher Propeller with 2 locating rings and
    instruction sheet

SPECIFICATIONS:
Length: 8" Pitch: 3.8"
Hub Thickness: 0.30" Hub size: 0.50"
Hole Size: 1/4"

REQUIRES:
Just for use with electric motors. Not for use with radiance or gasoline
    engines.
All props need balancing, this is ESSENTIAL, utilize TOPQ5700.
May requirement prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)