Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Plume) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Extremely slim case and lightweight for mounting in small planes,
    electrics or gliders, where extremely high speed and good torque are
    critical.
One of the slimmest micro servos available.
High-strength resin equipment train offers trusted operation.

INCLUDES:
One HS-55 Servo w/pre-installed small X-shaped servo horn and screw
One extremely small straight servo horn
One M1.7x3 servo horn screw
One small straight servo horn
2 M1.7x7 servo mounting screws

at 4.8V
SPECIFICATIONS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

This item is frequently purchased with the above stated item.



This is the Futaba S3003 Requirement Servo.
This fundamental servo is used in vehicles, boats, or where standard servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If utilizing NiMH or LiPo batteries, ensure they are capable
of delivering sufficient amps.

INCLUDES:
One S3003 standard servo with preinstalled Xshape servo horn FUTM0031
Four brass eyelets
Four Black rectangle-shaped rubber grommets (FUTM2348)
Four servo mount screws
One servo wheel 1-3/8" (35mm) in size
One X-shape servo arm 1.5" (38mm) throughout
One star shaped arm 1-1/4" (32mm) throughout
Nylon gears
One year service warranty

SPECIFICATIONS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Measurements: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Port: "J" type with approx. 5" lead

Frequently purchased with the item that you are currently reading about.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") airplane propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design offers these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon construction lowers rotating mass for
    greater output and longer life.
Reinforcing carbon fibers help maintain true, consistent pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of small shaft finding rings
One finding ring direction sheet

NEEDS:
ALL props need balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not created for Radiance engines

The listed below item also sets actually well with the item being reviewed.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FUNCTIONS:
Light-weight molded nylon construction lowers rotating mass for
    greater output and longer life
Developed for electrical powered Park Flyer type aircraft with rear
    facing motors that "push" the airplane forward

INCLUDES:
8x3.8 Slo-Flyer Pusher Propeller with two finding rings and
    direction sheet

SPECIFICATIONS:
Length: 8" Pitch: 3.8"
Center Thickness: 0.30" Center size: 0.50"
Hole Size: 1/4"

NEEDS:
Only for use with electrical motors. Not for use with radiance or gasoline
    engines.
All props need balancing, this is VERY important, utilize TOPQ5700.
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)