Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Plume) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Really slim case and lightweight for installing in small planes,
    electrics or gliders, where really high speed and good torque are
    critical.
One of the slimmest micro servos available.
High-strength resin gear train offers reliable operation.

INCLUDES:
One HS-55 Servo w/pre-installed small X-shaped servo horn and screw
One really small straight servo horn
One M1.7x3 servo horn screw
One small straight servo horn
Two M1.7x7 servo installing screws

at 4.8V
SPECS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

This product is often gotten with the above stated product.



This is the Futaba S3003 Standard Servo.
This standard servo is utilized in automobiles, boats, or where basic servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If utilizing NiMH or LiPo batteries, make certain they are capable
of providing adequate amps.

INCLUDES:
One S3003 basic servo with preinstalled Xshape servo horn FUTM0031
4 brass eyelets
4 Black rectangle-shaped rubber grommets (FUTM2348)
4 servo mount screws
One servo wheel 1-3/8" (35mm) in size
One X-shape servo arm 1.5" (38mm) throughout
One star shaped arm 1-1/4" (32mm) throughout
Nylon equipments
One year warranty

SPECS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Dimensions: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Port: "J" type with approx. 5" lead

Frequently gotten with the product that you are currently reading about.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") aircraft propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design gives these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon building minimizes turning mass for
    greater output and longer life.
Reinforcing carbon fibers help maintain real, continuous pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of small shaft locating rings
One locating ring direction sheet

REQUIRES:
ALL props need balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Length: 8"
Pitch: 3.8

COMMENTS:
Slo-Flyer props are Not created for Radiance engines

The below product likewise pairs really well with the product being talked about.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FEATURES:
Light-weight molded nylon building minimizes turning mass for
    greater output and longer life
Developed for electrical powered Park Flyer type aircraft with rear
    facing motors that "push" the aircraft forward

CONSISTS OF:
8x3.8 Slo-Flyer Pusher Propeller with two locating rings and
    direction sheet

SPECS:
Length: 8" Pitch: 3.8"
Center Thickness: 0.30" Center size: 0.50"
Hole Diameter: 1/4"

REQUIRES:
Just for use with electrical motors. Not for use with radiance or fuel
    engines.
All props need balancing, this is EXTREMELY IMPORTANT, use TOPQ5700.
May requirement prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)