Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Feather) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Really slim case and light-weight for mounting in little planes,
    electrics or gliders, where extremely high speed and good torque are
    critical.
One of the slimmest micro servos available.
High-strength resin equipment train provides reputable operation.

INCLUDES:
One HS-55 Servo w/pre-installed little X-shaped servo horn and screw
One extremely little straight servo horn
One M1.7x3 servo horn screw
One little straight servo horn
2 M1.7x7 servo mounting screws

at 4.8V
SPECIFICATIONS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

This item is frequently acquired with the above stated item.



This is the Futaba S3003 Standard Servo.
This basic servo is utilized in automobiles, boats, or where conventional servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If using NiMH or LiPo batteries, make certain they are capable
of providing sufficient amps.

INCLUDES:
One S3003 conventional servo with preinstalled Xshape servo horn FUTM0031
4 brass eyelets
4 Black rectangle-shaped rubber grommets (FUTM2348)
4 servo install screws
One servo wheel 1-3/8" (35mm) in diameter
One X-shape servo arm 1.5" (38mm) throughout
One star shaped arm 1-1/4" (32mm) throughout
Nylon equipments
One year service warranty

SPECIFICATIONS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Dimensions: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Port: "J" type with approx. 5" lead

Frequently acquired with the item that you are presently reading about.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") airplane propeller.
This prop produces a great deal of torque even at low speeds.

FEATURES:
Computer-optimized design offers these props a thinner profile and
    more "bite" with less noise.
Lightweight formed nylon construction decreases turning mass for
    higher output and longer life.
Reinforcing carbon fibers assist maintain real, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft finding rings
One finding ring direction sheet

REQUIRES:
ALL props need balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not developed for Radiance engines

The listed below item also sets truly well with the item being reviewed.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FUNCTIONS:
Lightweight molded nylon construction decreases turning mass for
    higher output and longer life
Developed for electric powered Park Leaflet type aircraft with rear
    dealing with motors that "push" the airplane forward

INCLUDES:
8x3.8 Slo-Flyer Pusher Propeller with 2 finding rings and
    direction sheet

SPECIFICATIONS:
Length: 8" Pitch: 3.8"
Hub Density: 0.30" Hub diameter: 0.50"
Hole Diameter: 1/4"

REQUIRES:
Just for usage with electric motors. Not for usage with radiance or gasoline
    engines.
All props need balancing, this is CRUCIAL, use TOPQ5700.
May requirement prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)