Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Plume) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Very slim case and lightweight for installing in little aircrafts,
    electrics or gliders, where extremely high speed and great torque are
    critical.
One of the slimmest micro servos available.
High-strength resin gear train supplies reputable operation.

INCLUDES:
One HS-55 Servo w/pre-installed little X-shaped servo horn and screw
One extremely little straight servo horn
One M1.7x3 servo horn screw
One little straight servo horn
Two M1.7x7 servo installing screws

at 4.8V
SPECS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

This item is regularly gotten with the above pointed out item.



This is the Futaba S3003 Requirement Servo.
This basic servo is utilized in cars, boats, or where basic servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If utilizing NiMH or LiPo batteries, make certain they are capable
of delivering enough amps.

INCLUDES:
One S3003 basic servo with preinstalled Xshape servo horn FUTM0031
4 brass eyelets
4 Black rectangular rubber grommets (FUTM2348)
4 servo install screws
One servo wheel 1-3/8" (35mm) in diameter
One X-shape servo arm 1.5" (38mm) throughout
One star shaped arm 1-1/4" (32mm) throughout
Nylon equipments
One year warranty

SPECS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Measurements: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Adapter: "J" type with approx. 5" lead

Regularly gotten with the item that you are presently reviewing.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") aircraft propeller.
This prop produces a great deal of torque even at low speeds.

FEATURES:
Computer-optimized design offers these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon building reduces turning mass for
    greater output and longer life.
Reinforcing carbon fibers assist maintain true, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft locating rings
One locating ring direction sheet

NEEDS:
ALL props require balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Length: 8"
Pitch: 3.8

COMMENTS:
Slo-Flyer props are Not designed for Glow engines

The listed below item additionally sets really well with the item being gone over.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FUNCTIONS:
Light-weight molded nylon building reduces turning mass for
    greater output and longer life
Developed for electrical powered Park Flyer type airplane with rear
    dealing with motors that "push" the aircraft forward

CONSISTS OF:
8x3.8 Slo-Flyer Pusher Propeller with two locating rings and
    direction sheet

SPECS:
Length: 8" Pitch: 3.8"
Center Thickness: 0.30" Center diameter: 0.50"
Hole Size: 1/4"

NEEDS:
Just for use with electrical motors. Not for use with radiance or gasoline
    engines.
All props require balancing, this is ESSENTIAL, use TOPQ5700.
May requirement prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)