Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Plume) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Extremely slim case and lightweight for mounting in small aircrafts,
    electrics or gliders, where really high speed and great torque are
    critical.
One of the slimmest micro servos available.
High-strength resin gear train provides reliable operation.

INCLUDES:
One HS-55 Servo w/pre-installed small X-shaped servo horn and screw
One really small straight servo horn
One M1.7x3 servo horn screw
One small straight servo horn
Two M1.7x7 servo mounting screws

at 4.8V
SPECIFICATIONS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

This product is often gotten with the above discussed product.



This is the Futaba S3003 Requirement Servo.
This fundamental servo is utilized in cars, boats, or where basic servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If utilizing NiMH or LiPo batteries, ensure they are capable
of delivering adequate amps.

INCLUDES:
One S3003 basic servo with preinstalled Xshape servo horn FUTM0031
Four brass eyelets
Four Black rectangular rubber grommets (FUTM2348)
Four servo install screws
One servo wheel 1-3/8" (35mm) in size
One X-shape servo arm 1.5" (38mm) throughout
One star shaped arm 1-1/4" (32mm) throughout
Nylon gears
One year service warranty

SPECIFICATIONS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Dimensions: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Connector: "J" type with approx. 5" lead

Regularly gotten with the product that you are currently checking out.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") plane propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design provides these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon construction minimizes rotating mass for
    higher output and longer life.
Reinforcing carbon fibers assist keep real, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of small shaft finding rings
One finding ring guideline sheet

REQUIRES:
ALL props require balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

COMMENTS:
Slo-Flyer props are Not developed for Radiance engines

The listed below product additionally pairs actually well with the product being discussed.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FEATURES:
Lightweight molded nylon construction minimizes rotating mass for
    higher output and longer life
Developed for electric powered Park Flyer type aircraft with rear
    dealing with motors that "push" the plane forward

CONSISTS OF:
8x3.8 Slo-Flyer Pusher Propeller with two finding rings and
    guideline sheet

SPECIFICATIONS:
Length: 8" Pitch: 3.8"
Center Density: 0.30" Center size: 0.50"
Hole Diameter: 1/4"

REQUIRES:
Only for use with electric motors. Not for use with radiance or gas
    engines.
All props require balancing, this is VERY important, use TOPQ5700.
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)