Hitec Hs-55 Sub Micro Servo, .14Sec/18Oz @ 6.0V

    This is the Hitec HS-55 Sub Micro (Feather) Servo with a
Futaba J, Hitec S, JR, Airtronics Z-type Connector.

FEATURES:
Extremely slim case and lightweight for installing in little planes,
    electrics or gliders, where extremely high speed and good torque are
    critical.
One of the slimmest micro servos available.
High-strength resin gear train offers dependable operation.

INCLUDES:
One HS-55 Servo w/pre-installed little X-shaped servo horn and screw
One extremely little straight servo horn
One M1.7x3 servo horn screw
One little straight servo horn
2 M1.7x7 servo installing screws

at 4.8V
SPECS:
Speed: 0.17 sec at 60°
Output Torque: 15.27 oz-in (1.1 kg-cm)
Weight: 0.27oz (7.8g)
Length: 0.89" (22.8mm)
Width: 0.45" (11.6mm)
Height: 0.94" (24mm)

This item is frequently bought with the above pointed out item.



This is the Futaba S3003 Requirement Servo.
This fundamental servo is used in automobiles, boats, or where standard servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.

This servo can produce high-current draw from your batteries.
If utilizing NiMH or LiPo batteries, make certain they are capable
of delivering enough amps.

INCLUDES:
One S3003 standard servo with preinstalled Xshape servo horn FUTM0031
4 brass eyelets
4 Black rectangular rubber grommets (FUTM2348)
4 servo mount screws
One servo wheel 1-3/8" (35mm) in size
One X-shape servo arm 1.5" (38mm) across
One star shaped arm 1-1/4" (32mm) across
Nylon equipments
One year service warranty

SPECS:
Speed: 0.23 sec/60° @ 4.8V
0.19 sec/60° @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Measurements: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
    (40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Adapter: "J" type with approx. 5" lead

Regularly bought with the item that you are currently reviewing.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") airplane propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design provides these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon construction reduces rotating mass for
    greater output and longer life.
Reinforcing carbon fibers help preserve real, consistent pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft finding rings
One finding ring instruction sheet

NEEDS:
ALL props need balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not developed for Radiance engines

The below item additionally pairs really well with the item being discussed.

8x3.8 Slow Flyer Pusher

This is an 8x3.8 Slo-Flyer Pusher Propeller from APC

FEATURES:
Light-weight molded nylon construction reduces rotating mass for
    greater output and longer life
Created for electric powered Park Flyer type aircraft with rear
    dealing with motors that "push" the airplane forward

CONSISTS OF:
8x3.8 Slo-Flyer Pusher Propeller with two finding rings and
    instruction sheet

SPECS:
Length: 8" Pitch: 3.8"
Center Thickness: 0.30" Center size: 0.50"
Hole Diameter: 1/4"

NEEDS:
Only for use with electric motors. Not for use with radiance or fuel
    engines.
All props need balancing, this is VERY important, utilize TOPQ5700.
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)