Hitec Hs-82Mg Standard Metal Gear Micro Servo .10Sec/47Oz @ 6.0V

    This is the HS-82MG Metal Equipment Micro Servo from Hitec.

FEATURES:
For little aircrafts, gliders, electrical helicopters and 1/18 scale vehicles

INCLUDES:
HS-82MG Metal Equipment Micro Servo with universal adapter, 0.67" (17mm)
    diameter horn, 1.1" (29mm) double arm, 0.90" (23mm) 4-point horn
    and mounting hardware

REQUIRES:
Installing in design and connecting to receiver

SPECS:
Speed: 0.12 sec/60° at 4.8V
0.10 sec/60° at 6.0V
Torque: 38.88oz-in (2.8kg-cm) at 4.8V
47.22oz-in (3.4kg-cm) at 6.0V
Weight: 0.66oz (19.0g)
Size: 1.17 x 0.47 x 1.16" (29.8 x 12.0 x 29.6mm)

REMARKS:
The following replacement parts are offered;
Equipment Set, HRCM6386
Horn Set, HRCM6326

Want another terrific product to enhance the above mentioned product?



This is the ElectriFly Silver Series 45 amp Brushless Electronic Speed Control.
Great for bigger high efficiency aircrafts. Providing
45A of continuous existing with an integrated Battery Circuit
which can manage 2A, this ESC is easy to utilize
and really affordable.

FEATURES:
Suitable with NiCd, NiMH and LiPo batteries
Auto-detects input volts and sets Low-Voltage cutoff
8.5kHz switching frequency, for excellent run time and cool operation
Pre-installed Universal radio adapter* (see Comments listed below)
Pre-installed WS Deans Ultra male adapter for battery (see
Comments listed below)
Pre-installed gold plated 4mm female bullet adapters for motor
High powered switching BEC (Battery Eliminator Circuit) which
    handles 3 or 4 basic servos
Full proportional forward and smooth throttle reaction with ON/OFF
    brake
Safe Start System** (see information in Comments listed below)
Thermal Protection stops motor when maximum temperature 230°F
    is reached
180 Day Service warranty (U.S.A & Canada Only)

INCLUDES:
One Brushless ElectriFly Silver Series 45A Speed Control with
    pre-installed receiver adapter, battery adapter, and motor
    adapters.

REQUIRES:
Mating motor connectors, use: GPMM3114
Mating battery adapter, use: WSDM3000

SPECS:
Length: 2.76" (70mm)
Width: 1.30" (33mm)
Height: .39" (10mm)
Weight: 1.76oz (50g)
Input Voltage: 6-12 cells NiCd/NiMH
2-4 cells LiPo
(20V input w/o BEC)
Output Current: 45A continuous maximum
50A rise maximum
Max Output Power: 500 watts
ON-resistance: .008 ohms
Operating frequency: 16kHz repaired
BEC: 5V/2A
Low Voltage Cutoff: Battery voltage x .67
Thermal Cutoff: 230°F (110°C)
Timing Angle: 20°
Brake: ON/OFF

REMARKS:
To utilize with "Old Airtronics" Rx, requires adapter: AIRM4400

**Safe Start System: Move throttle stay with complete throttle position,
then to "OFF" position, then slowly advance throttle and motor will
begin to run.

The "Silver Series" line of brushless electronic speed controls
    such as many integrated security functions. One such feature COULD
    POTENTIALLY CAUSE THE BRUSHLESS MOTOR TO STOP ROTATING when the
    transmitter's stick is at a very low position and/or if
    rotation of the brushless motor is hampered or obstructed in some
    method. This is NORMAL, as the ESC is detecting that a problem
    potentially exists with the motor and/or speed control. Rotation of
    the motor is stopped to secure the speed control from possible
    damage.
WARNING!!
If the ESC and motor have actually currently been equipped and the motor has been
rotating typically, yet after moving the throttle stay with near minimum the
motor suddenly ceases to turn typically even if the throttle stick is advanced
above minimum throttle, DO NOT PLACE YOUR HANDS NEAR THE PROPELLER!! FAILURE
TO
OBEY THIS WARNING COULD LEAD TO PERSONAL INJURY!! From this point, moving
the throttle hold up - even to complete throttle may not trigger the motor to
turn BUT THE MOTOR IS STILL ARMED AND ACTIVE DURING THIS TIME!! To regain
control of the motor, move the throttle stay with absolute minimum throttle
position then advance the throttle stick up-wards when again.
Alternatively, you can disconnect the battery from the ESC, then re-connect the
power source and re-arm the system.
NEVER
get near the propeller if the speed control is linked to input power!
ALWAYS
make certain the throttle stick is at minimum position before trying to
disconnect the battery from the speed control! ElectriFly is not accountable
for incidental damage or injury as a result of misuse of this item.