Great Planes Rimfire Prop Saver 28mm Motors

This is the ElectriFly Rimfire Prop Saver for use on 28mm Motors.

FEATURES:
Aluminum construction

INCLUDES:
One Prop Saver
Two Rubber O-Rings
Two Bushings

NEEDS:
Setup on Rimfire 28mm Motor

Below is a wonderful item that several others have purchased the same time.

Tower Pro SG90 Servo

Functions:
Micro Servo Titan 9g servo
Gear Type : All Nylon Gear
Dead Band Width : 2 usec
Stall Torque : 1.5kg/cm at 4.8V
Operation Voltage : 3.0 - 7.2Volts

Specifications:
Dimension : 23mm x 12mm x 29mm
Adapter Wire Length : About 248mm
Running Speed : 0.12sec / 60 degrees (4.8V no load)
Temperature level Variety : -30 to +60 Degree C
Net weight : about 11g
Color : black

Packaging content:
1 x 9g TITAN Servo Sets (with devices)

This item praises the above gone over item.

930Kv Brushless Outrunner Motor, 3.17 MM Shaft, 3.5MM Bullet Con

LI-Poly Cell:2-3
Ni-MH Cells: 6-10
RPM/V: 1800Kv
Max. efficiency present: 6-10 Amp
NoLoad current / 10 V: 0.8 Amp
Present capability: 16 A/60 s
Max. Efficiency: 74%
Shaft diameter: 3mm

A2208-12 much like: AXI 2208/20, E-Flite Park 370

This item praises the main item below.

6x4 Thin Electric Prop

This is a 6x4E Thin Composite propeller from Advanced Accuracy Composites.
For use on Electric powered aircraft just (not for glow engines).

FEATURES:
Gray composite propeller blades that assemble onto a propeller hub.
Comes with 2 adapter rings that adapt to various motor shafts.
Comes in a bag connected to a header card.

INCLUDES:
One composite propeller
Two composite adapter rings
One direction sheet

NEEDS:
Assembly onto motor or equipment drive system in your Electric plane.
Balancing

SPECIFICATIONS:
Size: 6"
Pitch: 4
Center inner diameter: 0.25"

REMARKS:
Usage Speed 400 Electric motors.

Below is a wonderful item that several others have purchased the same time.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") airplane propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design provides these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon construction minimizes rotating mass for
    greater output and longer life.
Reinforcing carbon fibers assist maintain real, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of small shaft finding rings
One finding ring direction sheet

NEEDS:
ALL props need balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not created for Glow engines

Below is one more item that praises the item being gone over.

7x6E Thin Electric

This is a 7x6EP Thin Propeller from Advanced Accuracy Composites.
For use on electric powered aircraft just (not for glow engines).

FEATURES:
Gray composite construction
Includes 2 adapter rings that adapt to various motor shafts

INCLUDES:
One 7x6EP Thin Electric Propeller

NEEDS:
ALL props need balancing, this is EXTREMELY essential, use TOPQ5700.
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Size: 7"
Pitch: 6
Center inner diameter: 0.25" (6.3mm)