Great Planes Rimfire Prop Saver 28mm Motors

This is the ElectriFly Rimfire Prop Saver for usage on 28mm Motors.

FEATURES:
Aluminum construction

INCLUDES:
One Prop Saver
2 Rubber O-Rings
2 Bushings

REQUIRES:
Installation on Rimfire 28mm Motor

Below is a great item that several others have bought at the very same time.

Tower Pro SG90 Servo

Functions:
Micro Servo Titan 9g servo
Gear Type : All Nylon Gear
Dead Band Width : 2 usec
Stall Torque : 1.5kg/cm at 4.8V
Operation Voltage : 3.0 - 7.2Volts

Requirements:
Measurement : 23mm x 12mm x 29mm
Connector Wire Length : About 248mm
Operating Speed : 0.12sec / 60 degrees (4.8V no load)
Temperature Range : -30 to +60 Degree C
Net weight : about 11g
Color : black

Packaging material:
1 x 9g TITAN Servo Sets (with devices)

This item praises the above discussed item.

930Kv Brushless Outrunner Motor, 3.17 MM Shaft, 3.5MM Bullet Con

LI-Poly Cell:2-3
Ni-MH Cells: 6-10
RPM/V: 1800Kv
Max. effectiveness existing: 6-10 Amp
NoLoad current / 10 V: 0.8 Amp
Present capability: 16 A/60 s
Max. Effectiveness: 74%
Shaft size: 3mm

A2208-12 similar to: AXI 2208/20, E-Flite Park 370

This item praises the main item below.

6x4 Thin Electric Prop

This is a 6x4E Thin Composite propeller from Advanced Accuracy Composites.
For utilize on Electric powered airplane just (not for glow engines).

FEATURES:
Gray composite propeller blades that put together onto a propeller hub.
Comes with 2 adjuster rings that adapt to various motor shafts.
Comes in a bag attached to a header card.

INCLUDES:
One composite propeller
2 composite adapter rings
One guideline sheet

REQUIRES:
Assembly onto motor or equipment drive unit in your Electric plane.
Balancing

SPECS:
Diameter: 6"
Pitch: 4
Center inner size: 0.25"

REMARKS:
Use Speed 400 Electric motors.

Below is a great item that several others have bought at the very same time.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") plane propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design provides these props a thinner profile and
    more "bite" with less noise.
Lightweight formed nylon construction reduces rotating mass for
    higher output and longer life.
Reinforcing carbon fibers assist maintain true, consistent pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of small shaft locating rings
One locating ring guideline sheet

REQUIRES:
ALL props need balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not created for Glow engines

Below is another item that praises the item being discussed.

7x6E Thin Electric

This is a 7x6EP Thin Propeller from Advanced Accuracy Composites.
For utilize on electrical powered airplane just (not for glow engines).

FEATURES:
Gray composite construction
Includes 2 adjuster rings that adapt to various motor shafts

INCLUDES:
One 7x6EP Thin Electric Propeller

REQUIRES:
ALL props need balancing, this is REALLY essential, utilize TOPQ5700.
May requirement prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Diameter: 7"
Pitch: 6
Center inner size: 0.25" (6.3mm)