Great Planes Rimfire Prop Saver 28mm Motors

This is the ElectriFly Rimfire Prop Saver for usage on 28mm Motors.

FEATURES:
Aluminum building and construction

INCLUDES:
One Prop Saver
Two Rubber O-Rings
Two Bushings

NEEDS:
Installation on Rimfire 28mm Motor

Right here is a terrific product that numerous others have actually purchased the same time.

Tower Pro SG90 Servo

Features:
Micro Servo Titan 9g servo
Gear Type : All Nylon Gear
Dead Band Width : 2 usec
Stall Torque : 1.5kg/cm at 4.8V
Operation Voltage : 3.0 - 7.2Volts

Requirements:
Dimension : 23mm x 12mm x 29mm
Port Wire Length : About 248mm
Running Speed : 0.12sec / 60 degrees (4.8V no load)
Temperature Range : -30 to +60 Degree C
Net weight : about 11g
Color : black

Packing material:
1 x 9g TITAN Servo Sets (with devices)

This product compliments the above reviewed product.

930Kv Brushless Outrunner Motor, 3.17 MM Shaft, 3.5MM Bullet Con

LI-Poly Cell:2-3
Ni-MH Cells: 6-10
RPM/V: 1800Kv
Max. performance current: 6-10 Amp
NoLoad current / 10 V: 0.8 Amp
Existing capacity: 16 A/60 s
Max. Performance: 74%
Shaft diameter: 3mm

A2208-12 similar to: AXI 2208/20, E-Flite Park 370

This product compliments the main item right here.

6x4 Thin Electric Prop

This is a 6x4E Thin Composite propeller from Advanced Precision Composites.
For utilize on Electric powered aircraft just (not for radiance engines).

FUNCTIONS:
Gray composite propeller blades that assemble onto a propeller hub.
Comes with 2 adapter rings that adapt to different motor shafts.
Comes in a bag attached to a header card.

INCLUDES:
One composite propeller
Two composite adapter rings
One guideline sheet

NEEDS:
Assembly onto motor or equipment drive system in your Electric plane.
Balancing

SPECIFICATIONS:
Diameter: 6"
Pitch: 4
Center inner diameter: 0.25"

COMMENTS:
Use Speed 400 Electric motors.

Right here is a terrific product that numerous others have actually purchased the same time.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") airplane propeller.
This prop produces a great deal of torque even at low speeds.

FEATURES:
Computer-optimized design provides these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon building and construction minimizes turning mass for
    higher output and longer life.
Reinforcing carbon fibers help maintain real, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft finding rings
One finding ring guideline sheet

NEEDS:
ALL props need balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

COMMENTS:
Slo-Flyer props are Not created for Radiance engines

Right here is another product that compliments the product being reviewed.

7x6E Thin Electric

This is a 7x6EP Thin Propeller from Advanced Precision Composites.
For utilize on electric powered aircraft just (not for radiance engines).

FUNCTIONS:
Gray composite building and construction
Features 2 adapter rings that adapt to different motor shafts

INCLUDES:
One 7x6EP Thin Electric Propeller

NEEDS:
ALL props need balancing, this is VERY vital, utilize TOPQ5700.
May requirement prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Diameter: 7"
Pitch: 6
Center inner diameter: 0.25" (6.3mm)