Great Planes Rimfire Prop Saver 28mm Motors

This is the ElectriFly Rimfire Prop Saver for usage on 28mm Motors.

FEATURES:
Aluminum building

SUCHES AS:
One Prop Saver
Two Rubber O-Rings
Two Bushings

REQUIRES:
Installation on Rimfire 28mm Motor

Here is a wonderful product that numerous others have actually bought at the very same time.

Tower Pro SG90 Servo

Functions:
Micro Servo Titan 9g servo
Equipment Type : All Nylon Equipment
Dead Band Width : 2 usec
Stall Torque : 1.5kg/cm at 4.8V
Operation Voltage : 3.0 - 7.2Volts

Requirements:
Measurement : 23mm x 12mm x 29mm
Adapter Wire Length : About 248mm
Operating Speed : 0.12sec / 60 degrees (4.8V no load)
Temperature Variety : -30 to +60 Degree C
Net weight : about 11g
Color : black

Packing content:
1 x 9g TITAN Servo Sets (with accessories)

This product praises the above talked about product.

930Kv Brushless Outrunner Motor, 3.17 MM Shaft, 3.5MM Bullet Con

LI-Poly Cell:2-3
Ni-MH Cells: 6-10
RPM/V: 1800Kv
Max. performance current: 6-10 Amp
NoLoad current / 10 V: 0.8 Amp
Present capacity: 16 A/60 s
Max. Performance: 74%
Shaft diameter: 3mm

A2208-12 just like: AXI 2208/20, E-Flite Park 370

This product praises the main item right here.

6x4 Thin Electric Prop

This is a 6x4E Thin Composite propeller from Advanced Accuracy Composites.
For use on Electric powered aircraft just (not for radiance engines).

FUNCTIONS:
Gray composite propeller blades that put together onto a propeller hub.
Comes with two adjuster rings that adapt to various motor shafts.
Comes in a bag attached to a header card.

INCLUDES:
One composite propeller
Two composite adapter rings
One direction sheet

REQUIRES:
Assembly onto motor or gear drive system in your Electric plane.
Balancing

SPECS:
Size: 6"
Pitch: 4
Center inner diameter: 0.25"

COMMENTS:
Use Speed 400 Electric motors.

Here is a wonderful product that numerous others have actually bought at the very same time.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") airplane propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design gives these props a thinner profile and
    more "bite" with less noise.
Lightweight formed nylon building reduces rotating mass for
    greater output and longer life.
Reinforcing carbon fibers assist keep true, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft locating rings
One locating ring direction sheet

REQUIRES:
ALL props require balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Length: 8"
Pitch: 3.8

COMMENTS:
Slo-Flyer props are Not created for Glow engines

Here is another product that praises the product being talked about.

7x6E Thin Electric

This is a 7x6EP Thin Propeller from Advanced Accuracy Composites.
For use on electric powered aircraft just (not for radiance engines).

FUNCTIONS:
Gray composite building
Includes two adjuster rings that adapt to various motor shafts

SUCHES AS:
One 7x6EP Thin Electric Propeller

REQUIRES:
ALL props require balancing, this is REALLY crucial, use TOPQ5700.
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Size: 7"
Pitch: 6
Center inner diameter: 0.25" (6.3mm)