Great Planes Rimfire Prop Saver 28mm Motors

This is the ElectriFly Rimfire Prop Saver for use on 28mm Motors.

FEATURES:
Aluminum building and construction

CONSISTS OF:
One Prop Saver
2 Rubber O-Rings
2 Bushings

REQUIRES:
Installation on Rimfire 28mm Motor

Below is a excellent item that numerous others have actually bought at the same time.

Tower Pro SG90 Servo

Functions:
Micro Servo Titan 9g servo
Equipment Type : All Nylon Equipment
Dead Band Width : 2 usec
Stall Torque : 1.5kg/cm at 4.8V
Operation Voltage : 3.0 - 7.2Volts

Requirements:
Measurement : 23mm x 12mm x 29mm
Port Wire Length : About 248mm
Running Speed : 0.12sec / 60 degrees (4.8V no load)
Temperature level Variety : -30 to +60 Degree C
Net weight : about 11g
Color : black

Packing material:
1 x 9g TITAN Servo Sets (with accessories)

This item compliments the above discussed item.

930Kv Brushless Outrunner Motor, 3.17 MM Shaft, 3.5MM Bullet Con

LI-Poly Cell:2-3
Ni-MH Cells: 6-10
RPM/V: 1800Kv
Max. efficiency present: 6-10 Amp
NoLoad current / 10 V: 0.8 Amp
Current capability: 16 A/60 s
Max. Effectiveness: 74%
Shaft diameter: 3mm

A2208-12 much like: AXI 2208/20, E-Flite Park 370

This item compliments the main item below.

6x4 Thin Electric Prop

This is a 6x4E Thin Composite propeller from Advanced Precision Composites.
For use on Electric powered airplane only (not for glow engines).

FUNCTIONS:
Gray composite propeller blades that put together onto a propeller hub.
Comes with 2 adjuster rings that adapt to various motor shafts.
Comes in a bag attached to a header card.

INCLUDES:
One composite propeller
2 composite adapter rings
One guideline sheet

REQUIRES:
Assembly onto motor or equipment drive system in your Electric plane.
Balancing

SPECS:
Diameter: 6"
Pitch: 4
Hub inner diameter: 0.25"

COMMENTS:
Usage Speed 400 Electric motors.

Below is a excellent item that numerous others have actually bought at the same time.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") airplane propeller.
This prop produces a great deal of torque even at low speeds.

FEATURES:
Computer-optimized design gives these props a thinner profile and
    more "bite" with less noise.
Lightweight formed nylon building and construction lowers turning mass for
    greater output and longer life.
Reinforcing carbon fibers help maintain true, consistent pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft locating rings
One locating ring guideline sheet

REQUIRES:
ALL props need balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Length: 8"
Pitch: 3.8

COMMENTS:
Slo-Flyer props are Not developed for Glow engines

Below is one more item that compliments the item being discussed.

7x6E Thin Electric

This is a 7x6EP Thin Propeller from Advanced Precision Composites.
For use on electrical powered airplane only (not for glow engines).

FUNCTIONS:
Gray composite building and construction
Comes with 2 adjuster rings that adapt to various motor shafts

CONSISTS OF:
One 7x6EP Thin Electric Propeller

REQUIRES:
ALL props need balancing, this is VERY important, use TOPQ5700.
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Diameter: 7"
Pitch: 6
Hub inner diameter: 0.25" (6.3mm)