E-Flite Power 10 Brushless Outrunner Motor, 1100Kv

Functions



Comparable to a 10-size radiance engine for 32–48 ounce (910–1360 g) planesIdeal for 3D airplanes weighing 28–36 ounces (790–1020 g)Ideal for models requiring approximately 450 watts of powerHigh-torque, direct-drive option to inrunner brushless motorsIncludes mount, prop adapters and mounting hardwareExternal rotor design—5mm shaft can easily be reversed for alternative motor installationsSlotted 14-pole outrunner designHigh-quality construction with ball bearings and solidified steel shaftQuiet, light-weight operation




Summary


The Power 10 is created to deliver tidy and quiet power for 10-size sport and scale planes weighing 32 to 48 ounces (910 to 1360 grams), 3D planes weighing 28 to 36 ounces (790 to 1020 grams), or models requiring approximately 450 watts of power. It’s an especially great match for the E-flite Brio 10 for high speed F3A accuracy or creative aerobatics.







Tech Notes


* Maximum Operating Temperature: 220 degrees Fahrenheit
* Adequate cooling is needed for all motor operation at optimal present levels.
* Maximum Burst Current period is 15 seconds. Sufficient time in between maximum burst periods is needed for correct cooling and to avoid overheating the motor.
* Maximum Burst Current rating is for 3D and limited motor run flights. Lack of correct throttle management might result in damage to the motor considering that excessive usage of burst current might overheat the motor.

Examples of Aircraft Setups:
Please see our website for the most up-to-date information and aircraft setup examples.

NOTE: All information measured at complete throttle. Actual performance might differ depending on battery and flight conditions.
E-flite Brio 10

Motor: Power 10
ESC: E-flite 40A Brushless V2 (EFLA311B)
Prop: APC 12x6E (APC12060E)
Battery: Thunder Power PRO LITE 2100mAh 11.1V 3-Cell (THP21003SPL)
Flying Weight w/Battery: 2.1 pounds

Amps   Volts   Watts      Input Watts/Pound     RPM
37.2      9.6       357               170                 7800

Expect great speed and extreme vertical power for creative aerobatics. Typical period is roughly 6-9 minutes depending on throttle management.

E-flite Ultimate 20-300 10e

Motor: Power 10
ESC: E-flite 40A Lite Pro SB Brushless (EFLA1040L)
Prop: APC 12x6E (APC12060E)
Battery: Thunder Power 2600mAh 11.1V THREE PRO LITE V2 Li-Po (THP26003SPL2)
Flying Weight w/Battery: 40.7 oz (2.5)

Amps     Volts     Watts       Input Watts/Pound      RPM
40.2        10.7      430                    172               8350

Expect ballistic power very strong vertical performance ideal for pulling out of hovers. Typical period is roughly 5-8 minutes depending on throttle management.


You will require...
40A ESC
6- to 10-cell Ni-MH/Ni-Cd or 2–THREE Li-Po
10x5 to 12x6 electric props






Requirements


Type: Brushless outrunner motor
Size: 10-size
Bearings or Bushings: One 5 x 14 x 5mm Bearing, and One 5 x 11 x 5mm Bearing
Wire Gauge: 16
Suggested Prop Variety: 10x5–12x6
Voltage: 7.2–12
RPM/Volt (Kv): 1100
Resistance (Ri): .043 ohms
Idle Existing (Io): 2.10A @10V
Constant Existing: 32A
Maximum Burst Current: 42A (15 sec)
Cells: 6–10 Ni-MH/Ni-Cd or 2–THREE Li-Po
Speed Control: 35–40A brushless
Weight: 122 g (4.3 oz)
Overall Size: 35mm (1.40 in)
Shaft Size: 5mm (.20 in)
Overall Length: 43mm (1.60 in)






Articles, Reviews, and Hyperlinks




 Sneak peek: E-flite RV-9 450 ARF


 John Redman Helps United States Assemble The E-flite DHC-2 Beaver 25e


 Sneak peek – E-flite Nieuport 17 250 ARF


 John Redman shows us the new E-flite PT-19