Dubro 2.5Mm X 8 Socket Head Cap Screws (4/Pkg)

Dubro Socket Head Cap Screws are perfect for locations where a screwdriver won't
reach. They can be tighteded with an allen wrench or ball driver. The screws
come in a range of diameters and lengths. This utilizes a 2.5mm balldriver
(BONR1110).

Want one more fantastic thing to match the above mentioned thing?

2.5Mm X 6 Socket Head Cap Screws (4/Pkg)

Dubro Socket Head Cap Screws are perfect for locations where a screwdriver won't
reach. They can be tighteded with an allen wrench or ball driver. The screws
come in a range of diameters and lengths. This utilizes a 2.5mm balldriver
(BONR1110).

Get this thing to enhance the one you are reading about.

2.5Mm X 15 Socket Head Cap Screws (4/Pkg)

Dubro Socket Head Cap Screws are perfect for locations where a screwdriver won't
reach. They can be tighteded with an allen wrench or ball driver. The screws
come in a range of diameters and lengths. This utilizes a 2.5mm balldriver
(BONR1110).

This thing compliments the above gone over thing.

2.5Mm Steel Hex Nuts Metric(4)

These are 2.5mm Hex Nuts from Du-Bro's Vehicle Line (Metric).

FEATURES:
Zinc plated, steel metric hex nuts.
These are developed for use on R/C cars.

INCLUDES:
(4) Nuts

SPECS:
Diameter: 2.5mm

This is a fantastic enhancement to the thing currently being gone over.



Protect soft wood from "pull-through" screws and your hardware from rust with
Fantastic Airplanes' Zinc-plated washers. The washers include a large area
that spreads holding power to more material, letting you tighten up screws down
without damaging the surface area underneath. The special Zinc plating keeps them
rust and corrosion-free, for simple setup and removal.

INCLUDES:
Eight #2 Flat Washers and can be found in a reusable plastic parts pack

SPECS:
Inside Diameter: .095" (2.4mm)
Outside Diameter: .220" (5.5mm)

Often purchased with the thing that you are currently reading about.



The Leading Flite balancer is an ingenious method to stabilize your airplane or boat
propellers, spinner backplates, car wheels and tires, as well as numerous other
products in the pastime industry.

FEATURES:
Precision ground stabilizing shaft, held between two powerful
    "Ceramic 8" magnets permits shaft to "drift" for optimum sensitivity
Low-cost and simple to utilize...necessary for each modeler.
Reduces prop vibration-reducing engine wear and prevents
    structural damage
Can be utilized anywhere-on the workbench or at the field
Constructed of long-lasting, high impact plastic and Nickel steel
Consists of guidelines discussing ways to remedy out-of-balance props,
    as well as ways to utilize the balancer to figure out wind speed.
Can also be utilized to stabilize boat props, car wheels and tires,
    ducted fans, spinners, nose weights and more!
Balances approximately 24" propellers and any size wheels and tires.

INCLUDES:
Two Ceramic Magnets (GP# METAL058)
Two Molded Plastic Side Plates (GP# NYLON92)
Two Metal Rods for Base Assistance (GP# WIRES81)
One Balancing Shaft (TOPQ5701) or (GP# WIRES80)
Two Plastic Propeller Locking Cones (TOPQ5702)
Two Lexan Magnet Covers (GP# PSDC001)
Two Thumb Screws (GP# SCRW102) .

NEEDS:
CA to glue Lexan magnet covers to magnets.

SPECS:
Transport size: 2-1/8" x 7-1/8" x 1-5/16"
Assembled size: 2-1/8" x 7-1/8" x 7-3/8"

COMMENTS:
Balancer is EXTREMELY sensitive, EXTREMELY precise.