Castle Creations Cc Blower 15 Series For 1/8 Motors

This is the Motor Cooling Blower Fan and Shroud from Castle Creations.

FEATURES:
Fits motors with outside diameter in between 1-1/2 and 1-7/8"
    (38 - 47mm) such as the Castle Creations Neu-Castle 2200 and 2650
Connecteds into receiver and drops motor temperature level as much as 30°
One year minimal service warranty through producer start at date of
    purchase

SUCHES AS:
Fan with wire and connector, shroud and two zip ties

REQUIRES:
Attaching to motor can and connecteding into receiver

SPECIFICATIONS:
Length: 49mm
Width: 44.5mm
Height: 44.5mm
Wire Length: (9.5")

Want another fantastic product to compliment the above stated product?

Cc Blower Sct/Sv3 Fan

This is the Cooling Fan for the Castle Creations Sidewinder 3,
or Sidewinder SCT Electronic Speed Controls.

**Will not deal with older design cases utilized on the**
**non-waterproof Sidewinder SCT and initial Sidewinder 3.**

FFEATURES:
Snaps onto ESC, no screws needed

SUCHES AS:
Fan with Wire Lead and Connector
Fan Shroud

SPECIFICATIONS:
Input Voltage: 4.8 - 7.4V
Optimum RPM: 14,000
Wire Length: 11.4" (290mm)
Waterproof: NO, eliminate before exposing ESC to moisture

The listed below product also pairs actually well with the product being discussed.



This is the Castle Creations Sidewinder SV3 12V Electronic Speed Control
    and the 1406 Series 4600kV Sensorless Brushless Motor.

FEATURES:
SV3 12V ESC (CSEM0115)
Suggested for all 1/10 scale buggy and truggy applications that
    weigh less than 5lbs (2.25kg) all set to run (not for usage in much heavier
    vehicles such as E-Revos or E-Maxx class vehicles)
USB programming capability via Castle Link USB adapter (not suched as,
    order CSEM6300)
Waterproof for usage in nearly every environment (not intended for
    operation while submerged in liquid)
Reversible with reverse lockout
    1406 Series 4600kV Motor (CSEC0000)
540 size can replaces numerous stock brushed motors
Four magnet, 4 pole rotor for higher torque
1.4" diameter slotted stator
Easily removable end bell

SUCHES AS:
Sidewinder SV3 12V ESC with 13 gauge Battery Wires with Pre-Tinned
    Leads, 4mm Female Bullets for Motor Connection, Receiver Connector,
    On/Off Switch, Instructions, 4600kV 1406 series Brushless Motor
    with 4mm Male Bullet Connectors

REQUIRES:
Battery connector of modeler's choice

SPECIFICATIONS:
ESC;
Input Voltage: 2S LiPo minimum, 3S LiPo optimum, 9 cell NiCd/NiMH
Brake: Proportional
Reversible: Yes, with lockout
Measurements: 1.93 x 1.48 x 0.79" (49 x 38 x 20mm)
Weight: 1.96 oz (55.5 g) with 5" (127mm) long battery wires and no
    battery connector
    Motor;
kV Rating: 4600
Can Length: 1.9" (49mm)
Can Size: 1.4" (36mm)
Shaft Size: 1/8" (3.2mm)
Weight: 5.9 oz (169.5 g)
Connector: 4mm gold
Wire Length: 9.5" (241mm)

Lots of others have bought this product in addition to the product that you are presently reading about.

Motor Heat Sink

This is the initial replacement motor heatsink for the Traxxas Villain IV.
AXY
4/8/92

Below is another product that praises the product being discussed.

15T Pinion Gear 32P

This is a 15 Tooth 32 Pitch Pinion Equipment for the Traxxas E-Maxx Truck.
This is the equipment which is attached straight to the motor.

FEATURES:
Machined Steel
Created for a 3mm shaft

SUCHES AS:
One 15 tooth Pinion Equipment
One 3 x 4mm Set Screw

REQUIRES:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This equipment is just one of two which are utilized on the E-Maxx dual motor
    set-up.