Castle Creations Cc Blower 15 Series For 1/8 Motors

This is the Motor Cooling Blower Fan and Shroud from Castle Creations.

FEATURES:
Fits motors with outdoors size in between 1-1/2 and 1-7/8"
    (38 - 47mm) such as the Castle Creations Neu-Castle 2200 and 2650
Connecteds into receiver and drops motor temperature level as much as 30°
One year restricted service warranty through manufacturer beginning at date of
    purchase

SUCHES AS:
Fan with wire and connector, shroud and two zip ties

REQUIRES:
Connecting to motor can and plugging into receiver

SPECIFICATIONS:
Length: 49mm
Width: 44.5mm
Height: 44.5mm
Wire Length: (9.5")

Want an additional terrific item to compliment the above mentioned item?

Cc Blower Sct/Sv3 Fan

This is the Cooling Fan for the Castle Creations Sidewinder 3,
or Sidewinder SCT Electronic Speed Controls.

**Will not deal with older style cases utilized on the**
**non-waterproof Sidewinder SCT and original Sidewinder 3.**

FFEATURES:
Snaps onto ESC, no screws needed

SUCHES AS:
Fan with Wire Lead and Port
Fan Shroud

SPECIFICATIONS:
Input Voltage: 4.8 - 7.4V
Maximum RPM: 14,000
Wire Length: 11.4" (290mm)
Water resistant: NO, remove before exposing ESC to moisture

The below item additionally pairs truly well with the item being reviewed.



This is the Castle Creations Sidewinder SV3 12V Electronic Speed Control
    and the 1406 Series 4600kV Sensorless Brushless Motor.

FEATURES:
SV3 12V ESC (CSEM0115)
Advised for all 1/10 scale buggy and truggy applications that
    weigh less than 5lbs (2.25kg) ready to run (not for use in heavier
    automobiles such as E-Revos or E-Maxx class automobiles)
USB shows ability via Castle Link USB adapter (not consisted of,
    order CSEM6300)
Water resistant for use in almost every environment (not meant for
    operation while submerged in liquid)
Reversible with reverse lockout
    1406 Series 4600kV Motor (CSEC0000)
540 size can changes numerous stock brushed motors
Four magnet, four pole rotor for greater torque
1.4" size slotted stator
Removable end bell

SUCHES AS:
Sidewinder SV3 12V ESC with 13 gauge Battery Wires with Pre-Tinned
    Leads, 4mm Female Bullets for Motor Connection, Receiver Port,
    On/Off Switch, Directions, 4600kV 1406 series Brushless Motor
    with 4mm Male Bullet Connectors

REQUIRES:
Battery connector of modeler's choice

SPECIFICATIONS:
ESC;
Input Voltage: TWO LiPo minimum, THREE LiPo optimum, 9 cell NiCd/NiMH
Brake: Proportional
Reversible: Yes, with lockout
Dimensions: 1.93 x 1.48 x 0.79" (49 x 38 x 20mm)
Weight: 1.96 oz (55.5 g) with 5" (127mm) long battery wires and no
    battery connector
    Motor;
kV Rating: 4600
Can Length: 1.9" (49mm)
Can Size: 1.4" (36mm)
Shaft Size: 1/8" (3.2mm)
Weight: 5.9 oz (169.5 g)
Port: 4mm gold
Wire Length: 9.5" (241mm)

Many others have actually bought this item in addition to the item that you are presently reading about.

Motor Heat Sink

This is the original replacement motor heatsink for the Traxxas Bad guy IV.
AXY
4/8/92

Right here is an additional item that praises the item being reviewed.

15T Pinion Gear 32P

This is a 15 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the gear which is connected straight to the motor.

FEATURES:
Machined Steel
Created for a 3mm shaft

SUCHES AS:
One 15 tooth Pinion Gear
One 3 x 4mm Set Screw

REQUIRES:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This gear is only one of two which are utilized on the E-Maxx dual motor
    set-up.