Castle Creations Cc Blower 15 Series For 1/8 Motors

This is the Motor Cooling Blower Fan and Shroud from Castle Creations.

FEATURES:
Fits motors with outdoors size between 1-1/2 and 1-7/8"
    (38 - 47mm) such as the Castle Creations Neu-Castle 2200 and 2650
Plugs into receiver and drops motor temperature as much as 30°
One year minimal service warranty through maker start at date of
    purchase

CONSISTS OF:
Fan with wire and connector, shroud and two zip ties

NEEDS:
Attaching to motor can and plugging into receiver

SPECS:
Length: 49mm
Width: 44.5mm
Height: 44.5mm
Wire Length: (9.5")

Want an additional fantastic item to enhance the above mentioned item?

Cc Blower Sct/Sv3 Fan

This is the Cooling Fan for the Castle Creations Sidewinder 3,
or Sidewinder SCT Electronic Speed Controls.

**Will not work on older style cases used on the**
**non-waterproof Sidewinder SCT and initial Sidewinder 3.**

FFEATURES:
Snaps onto ESC, no screws needed

CONSISTS OF:
Fan with Wire Lead and Port
Fan Shroud

SPECS:
Input Voltage: 4.8 - 7.4V
Optimum RPM: 14,000
Wire Length: 11.4" (290mm)
Water resistant: NO, remove prior to exposing ESC to moisture

The below item likewise sets actually well with the item being talked about.



This is the Castle Creations Sidewinder SV3 12V Electronic Speed Control
    and the 1406 Series 4600kV Sensorless Brushless Motor.

FEATURES:
SV3 12V ESC (CSEM0115)
Suggested for all 1/10 scale buggy and truggy applications that
    weigh less than 5lbs (2.25kg) all set to run (not for usage in heavier
    vehicles such as E-Revos or E-Maxx class vehicles)
USB shows ability by means of Castle Link USB adapter (not suched as,
    order CSEM6300)
Water resistant for usage in almost every environment (not meant for
    operation while submerged in liquid)
Reversible with reverse lockout
    1406 Series 4600kV Motor (CSEC0000)
540 size can changes many stock brushed motors
4 magnet, 4 pole rotor for higher torque
1.4" size slotted stator
Easily removable end bell

CONSISTS OF:
Sidewinder SV3 12V ESC with 13 gauge Battery Wires with Pre-Tinned
    Leads, 4mm Female Bullets for Motor Connection, Receiver Port,
    On/Off Change, Instructions, 4600kV 1406 series Brushless Motor
    with 4mm Male Bullet Connectors

NEEDS:
Battery connector of modeler's choice

SPECS:
ESC;
Input Voltage: TWO LiPo minimum, 3S LiPo maximum, 9 cell NiCd/NiMH
Brake: Proportional
Reversible: Yes, with lockout
Dimensions: 1.93 x 1.48 x 0.79" (49 x 38 x 20mm)
Weight: 1.96 oz (55.5 g) with 5" (127mm) long battery wires and no
    battery connector
    Motor;
kV Score: 4600
Can Length: 1.9" (49mm)
Can Size: 1.4" (36mm)
Shaft Size: 1/8" (3.2mm)
Weight: 5.9 oz (169.5 g)
Port: 4mm gold
Wire Length: 9.5" (241mm)

Numerous others have purchased this item along with the item that you are presently checking out.

Motor Heat Sink

This is the initial replacement motor heatsink for the Traxxas Villain IV.
AXY
4/8/92

Right here is an additional item that praises the item being talked about.

15T Pinion Gear 32P

This is a 15 Tooth 32 Pitch Pinion Equipment for the Traxxas E-Maxx Truck.
This is the gear which is connected straight to the motor.

FEATURES:
Machined Steel
Developed for a 3mm shaft

CONSISTS OF:
One 15 tooth Pinion Equipment
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This gear is just one of two which are used on the E-Maxx double motor
    set-up.